HAKO Citymaster 2000 Скачать руководство пользователя

Страница: 18 / 186

2-2

X56b210.fm

Safety instructions

2.3 Designated use and exemption from liability

•

The Hako-Citymaster 2000 is used as tool carrier / machine for

industrial and municipality work around the year. This implies outdoor

cleaning by use of the sweeping unit, the suction port and the dirt

hopper as well as the optional winter service by use of a snow blade, a

sand or salt spreader and a pre-sweeper.
Every other application is regarded as not designated for the use of the

vehicle.

Hako-Werke GmbH will not be liable for damage resulting from use

other than mentioned above. The user alone will bear the risk.

Designated use also includes observing the instructions in the opera-

tion manual and observing the conditions of maintenance and service.

•

Observe the pertinent regulations relevant to accident prevention, other

generally acknowledged regulations regarding safety and occupational

medicine, as well as the regulations and standards relevant to motor

vehicles and traffic which are valid in your country. Hako-Werke GmbH

will not be liable for damage resulting from the failure to observe these

regulations.

•

The safety of the vehicle can be negatively affected by carrying out

vehicle modifications without proper authority and by using spare parts,

equipment, implements and optional equipment which have not been

checked and released by Hako-Werke GmbH. Hako-Werke GmbH will

not be liable for damage resulting from this.

Any unauthorised modification invalidates the Type Approval according

to §19(2) StVZO. The vehicle no longer complies with the model

described in the manufacturer documentation. This entitles the

manufacturer to refuse any warranty claims of the operator against the

manufacturer.

•

Hako-Werke GmbH will not be liable when:

•

Other implements are used than those checked and approved by
Hako-Werke GmbH

•

The service and maintenance work specified in the operation and
maintenance manual has not been performed correctly or not at all

•

Hako-Werke GmbH will not be liable for personal injury and/or damage

to property caused by failure to observe the safety instructions and the

operation manual, and by the negligence of the duty to exercise due

care when:

•

Handling

•

Operation

•

Servicing and carrying out maintenance work

•

Repairing

the vehicle.

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды