HAKO Citymaster 2000 Скачать руководство пользователя страница 160

Страница: 160 / 186

4-56

X56b540.fm

Maintenance

4.16 General maintenance work

4.16.1 Cleaning

Cleaning the vehicle is divided into 3 separate areas:

•

Inside the cab

•

Exterior of the vehicle

•

Engine compartment

The wrong choice of cleaning equipment and agents may impair the ope-

rating safety of the vehicle on the one hand, and on the other undermine

the health of the persons in charge of cleaning the vehicle. It is therefore

essential to observe the following instructions.

Environment!

Only use authorised washing places for cleaning the vehicle!

General instructions for all the
areas of the vehicle

When using washing solvents

•

Ensure adequate room ventilation

•

Wear suitable protective clothing

•

Do not use flammable liquids, such as petrol or diesel

When using compressed air

•

Work carefully

•

Wear goggles and protective clothing

•

Do not aim the compressed air at the skin or at other people

•

Do not use compressed air to clean your clothing

When using a high-pressure cleaner or steam jet

•

Keep a minimum distance of at least 30 cm!

•

Max. pressure 120 bar at max. 80°C

•

Cover electrical components and insulating mats, and do not expose

them directly to the jet

•

Do not expose the ventilation grid at the rear wall of the cab, the

breather filter of the hydraulic oil tank and the lids of the fuel and

hydraulic oil tanks etc. to the direct jet, or cover these parts

•

Protect the following components from moisture:

•

Electrical components, such as three-phase alternator, sensors,
electric plug and socket connections, engine control block etc..

•

Control devices and seals

•

Air intake filters etc.

When using volatile and easily flammable anticorrosion agents
and sprays:

•

Ensure adequate room ventilation

•

Avoid unprotected fire and light sources!

•

Do not smoke!

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды