manualshive.com logo in svg

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Поделиться
Скачать
HAKO Citymaster 2000 Скачать руководство пользователя страница 155

X56b540.fm 

4-51

Maintenance

Side turn indicators

To change the light bulbs of the side turn indicators

Important!

The light bulb can be changed without removing the turn indicator. 

The turn indicator has been dismantled in our illustration for a better 

explanation.

Remove plug 

J

 from turn indicator. To do thos:

•

Press in bow clip (arrow) and pull off plug 

K 

at the same time

Turn light bulb socket 90° counterclockwise whilst holding on the turn 

indicator
Pull light bulb socket out of the turn indicator
Slightly press down light bulb, turn half a turn and take out
Press in new light bulb, turn half a turn
Insert light bulb socket into the turn indicator
Turn light bulb socket 90° clockwise whilst holding on the turn indicator
Mount plug 

K

 until it locks with an audible click

J

K

Содержание Citymaster 2000



























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды