HAKO Citymaster 2000 Скачать руководство пользователя

Страница: 127 / 186

X56b520.fm

4-23

Maintenance

4.6 Hydraulic system

4.6.1

Specific safety instructions

•

All lines carrying hydraulic oil must be unpressurised prior to any

maintenance and repair work. To do this:

Lower all hydraulically controlled implements to the ground
Operate all controls for the work hydraulics several times

•

Apply the parking brake to prevent the vehicle from rolling away before

you carry out service and maintenance work

•

Hydraulic oil escaping under high pressure can penetrate the skin and

cause serious injuries. Always consult a doctor immediately even if the

wound seems insignificant – otherwise serious infections could set in!

•

Cloudy hydraulic oil in the sight glass indicates that water or air has

penetrated the hydraulic system. This may damage the hydraulic pump!

Contact your authorised Hako workshop immediately

•

Insufficient or incorrect hydraulic oil will damage the hydraulic system!

For this reason:

•

Only use authorised oils

•

Always top up the hydraulic oil before the level gets too low

•

If the hydraulic system is filled with biodegradable oil, then only use
biodegradable oil of the same type for topping up – observe the
sticker on the hydraulic oil tank!

•

You must contact our customer service if the hydraulic system filters
are soiled with metal chippings. Otherwise, follow-on damage may
result!

Important!

The hydraulic oil tank is located on the left side of the vehicle below

the tipper. The oil level can be checked in the sight glass.
• Check and top up, if necessary, the hydraulic oil level

weekly.

• Change the hydraulic oil

for the first time after 1200 operating

hours

at the latest every three years

• Change the hydraulic oil filter

for the first time after

50 operating hours

as well as regularly

every 1200 operating

hours, at the latest according to the fouling indicator

• Maintenance intervals for the hydraulic system (see page 4-63).

Environment!

Collect drained or spilt hydraulic oil in a suitable container and

dispose of it according to local or national environment protec-

tion regulations!

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды