HAKO Citymaster 2000 Скачать руководство пользователя

Страница: 71 / 186

X56b342.fm

3-43

Operation

3.4.11 Operator's seat/ passenger's seat

Danger!

Never change the seat position when driving or working –

Accident hazard!

Adjust the seat before moving the vehicle!
Observe the operation manual of the seat manufacturer!

Longitudinal adjustment A (driver's seat only)

Sit down on the operator’s seat

•

Pull lever

upward

•

Move the seat forward or backward

•

Release lever

and let the operator's seat engage

Height of rear edge of seat B (driver's seat only)

Sit down on the operator’s seat

•

Pull lever

upward

Height of front edge of seat C (driver's seat only)

Sit down on the operator’s seat

•

Pull lever

upward

Weight setting D (driver's seat only)

Important!

The driver seat has been equipped with a seat contact switch. In

case of excessive seat springing adjustment, travel drive cannot be

activated!

Use handwheel

to continuously adjust the seat suspension to the

operator's weight (possible ranges from 50 – 130 kg).

- Driving is only possible when the seat contact switch (driver’s

seat) is actuated.

- Acceleration is only possible when the seat contact switch

(driver’s seat) is actuated.

- Getting up from the driver’s seat (under 18kph) causes the vehicle

to stop.

- If the driver is not on the driver’s seat and the accelerator is pres-

sed or the hand throttle is actuated, the „SEAT CONTACT

SWITCH“ message appears in the vehicle’s multifunctional display.

Sit down on the operator’s seat

•

Turn handwheel

to adjust the seat suspension

Backrest adjustment E

Sit down on the operator’s seat

•

Press your back lightly against the backrest and pull up lever

at the

same time

•

Release lever

and let the backrest engage

Fig. 54:

Operation

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды