HAKO Citymaster 2000 Скачать руководство пользователя страница 54

Страница: 54 / 186

3-26

X56b320.fm

Operation

Parking brake lever

Function

•

To park the vehicle safely and to prevent it from rolling away (parking

brake)!

•

Emergency brake in the case of service brake breakdown

Danger!

Use the parking brake instead of the service brake in an

emergency only, i. e. in the case of a breakdown of the service

brake. This does not cause the brake lights to light. Accident

hazard!

Take machine to workshop without delay!
In normal operation, only use brake pedal

as a service brake.

Otherwise, the brake lights at the rear of the vehicle do not light

To prevent the vehicle rolling away

Pull the parking brake lever

upward to apply the parking brake.

The warning light

lights

A firm resistance must be felt after 6 to 8 notches.

Otherwise the parking brake is not in working order!

Have the parking brake immediately checked by a specialist

Danger!

The brake power of the parking brake depends on the rear

wheel with the lowest friction factor. When the vehicle is parked

on a slope with one rear wheel placed on solid and dry ground

while the other rear wheel is placed on ice or snow, the

maximum brake power is determined by the friction factor

between the wheel and the ice. Prevent the vehicle from rolling

away!

Accident hazard!

When parking the vehicle on a slope, additionally switch on

four wheel drive
When parking the vehicle on a slope, use chocks as well!

To release the parking brake

Slightly raise the parking brake lever, press button

on the parking

brake lever and lower the parking brake lever

The parking rake is released and warning light

goes off

Using the parking brake as secondary brake (only in an emer-
gency) while driving.

Pull parking brake lever

upward quickly

only in an emergency

Important!

The parking brake lever acts via a pull cable on a separate brake

drum on the gearbox shaft.

Fig. 23:

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Бренды по названию

Популярные бренды