HAKO Citymaster 2000 Скачать руководство пользователя

Страница: 72 / 186

3-44

X56b342.fm

Operation

Comfort seat (SO)

The following comfort seats are available as special equipment:

•

driver’s seat with air cushioning (1418)

•

driver’s seat with mechanical suspension (1419)

•

passenger’s seat with mechanical suspension (1420)

Please pay attention to the operating manual provided by the manufactu-

rer!

Head rest F (option)

Danger!

Do not drive if the head rest is not adjusted correctly!

Risk of injury!

Adjust the head rest so that the back of your head is suppor-

ted at the height of your ears

Sit down on the operator’s seat

•

Pull head rest

up or push down

•

Pull head rest

to the front or push it to the rear

3.4.12 Seat belt

Danger!

Do not drive or work with the seat belt undone –

Risk of injury!

Fasten the seat belt before moving or working with the

vehicle!

• Do not twist the seat belt!
• The seat belt must run across the pelvis – not the stomach

– and always sit firmly!

• Do not place the seat belt over hard, edged or breakable

objects

(tools, metre rules, glasses, pens) in your clothes!

• Never fasten 2 persons (children!) with one seat belt!
• Check seat belt condition regularly. Have damaged parts

immediately replaced by your authorised Hako workshop!

• Always keep seat belt clean, because coarse contamina-

tion can affect the function of the automatic belt!

• The lock may not be jammed by foreign objects (paper or

similar) otherwise the buckle latch cannot lock into place!

The seat belt is stretched after an accident, and can no longer

be used. Therefore, in case of an accident, this overstretched

belt strap is

Not safe any longer!

Replace the seat belt after an accident!
Have anchor points and seat attachment checked for further

load resistance!

Abb. 55:

Содержание Citymaster 2000



























































































































































































Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды

HAKO Citymaster 2000, Инструкция по эксплуатации и обслуживанию

Результаты поиска

Содержание Citymaster 2000

Отзывы:

Похожие инструкции для Citymaster 2000

Бренды по названию

Популярные бренды