manualshive.com logo in svg

GST GST102A, Инструкция по установке и эксплуатации

Поделиться
Скачать
GST GST102A Скачать руководство пользователя страница 32

GST102A/GST104A/GST108A/GST116A 
Conventional Fire Alarm Control Panel

   

Installation and Operation Manual 

Page

  27 

 

3.7 

Setting Auxiliary Functions 

 

RESOUND  MODE:  When  the  “6”  of  SW2  (

RESOUND  MODE

)  is  set  to  the  ON  position, 

resound  mode  is  turned  on.  When  there  is  fire  alarm  from  a  zone,  the  sounder  outputs 
associated to this zone will be started. Pressing 

SILENCE/RESOUND ALARM 

key and these 

sounder outputs can be silenced; if there is an alarm signal from another zone at this moment, 
the silenced sounder outputs that are not associated to this new alarm zone will resound. If 
resound mode is turned off, the silenced sounder outputs not associated to this new alarm 
zone will remain silenced. Default setting is ON. 

 

SILENCE RESET MODE: When the “7” of SW2 (

SIL-RESET MODE

) is set to the ON position, 

silence-reset  mode  is  turned  on.  When  there  is  fire  alarm  from  a  zone  and  its  associated 
sounder outputs are started, the CIE will not be reset until the sounder outputs are silenced. If 
silence-reset mode is turned off, the CIE can be reset immediately. Default setting is ON. 

 

SILENCE DELAY MODE: When the “8” of SW2 (

SIL-DEALY MODE

) is set to the ON position, 

silence-delay  mode  is  turned  on.  When  there  is  fire  alarm  from  a  zone  and  its  associated 
sounder  outputs  are  started,  the  CIE  has  to  stay  in  fire  condition  for  3  minutes  before  the 
sounder outputs could be silenced. If silence-delay mode is turned off, the sounder outputs 
can be silenced immediately. Default setting is OFF. 

 

DISABLE/SUPERVISED OUTPUT MODE: When the “6” of SW3 (

DIS. / SUP. OUT

) is set to 

the OFF position, the disable/supervised relay output is set for disable output; otherwise, this 
output is set for supervised output. Default setting is OFF. 

 

RELAY OUTPUT MODE: When the “7” of SW3 (

RELAY OUTPUT

) is set to the OFF position, 

the FAULT1 to FAULT16 on relay board are defaulted as fault outputs. When the “7” of SW3 
(

RELAY OUTPUT

) of is set to the ON position, FAULT1 to FAULT16 on relay board are set to 

general fire trips, which all will activate on any zone fire alarm. Default setting is OFF. 

☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆

 

Note: The auxiliary function has not been tested in EN54-2/4.

 

 

☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆

 

3.8 

Ground Fault Detection 

The CIE can detect a ground fault by connecting the X6(

EARTH FAULT

) with a jumper. Otherwise, 

the CIE does not detect a ground fault. 

3.9 

Auxiliary Power Setting 

Shorting “24V” and “AUX” of X3 with a jumper, the 

AUX SUPPLY

 output will be constant. If shorting 

“AUX” and “LOOP” of X3, the 

AUX SUPPLY

 output will drop for about 10 seconds when the CIE is 

reset. 

Содержание GST102A












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды