manualshive.com logo in svg

GST GST102A, Инструкция по установке и эксплуатации

Поделиться
Скачать
GST GST102A Скачать руководство пользователя страница 25

GST102A/GST104A/GST108A/GST116A 
Conventional Fire Alarm Control Panel

   

Installation and Operation Manual 

Page

  20 

 

There are two ways for using disablement function: basic steps and quick disablement.   

☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆

 

Note: Disable status setting will be saved even if the CIE is powered off.   

☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆☆

 

3.3.2 

Operation Basic Steps – Generally used for individually Disabling Zones or Sounder 

/Alarm Outputs when the panel is in normal operation mode. 

1) 

Enter access Level II as described in Section 3.1.2. 

2) 

Pressing the 

DISABLE/ENABLE

 button will illuminate the amber LED directly above it steadily.   

At the same time the amber LED of zone 1 will start flashing to show zone 1 is selected for 
disablement setup. The DISABLE LED illuminates steadily when any disablement event occurs. 
The 

FAULT

 LED will indicate according to the CIE fault condition. Other indicators, except for 

the above mentioned LEDs, will be turned off.   

3) 

Pressing  the 

SCROLL

  button  will  toggle  through  zones  1  to  16  and  the  Sounder  Outputs.   

Please note the Alarm Output is not able to be Disabled.       

4) 

The AMBER LED for zones 1 to 16 will flash when the zone is to be selected. Pressing the 

ENTER

 button will confirm the selection of the zone or output selected. That zone or output is 

now Disabled.    The illuminating 

DISABLE 

LED indicates the zone is disabled for that zone or 

output.   

5) 

When disabling Sounder Outputs the 

SOUNDER X FLT/DIS

 LED will flash when a sounder 

output is to be selected. Pressing the 

ENTER

 button will confirm your selection of this output 

and disable it. The illuminating 

DISABLE

 LED indicates the sounder output selected is disabled.   

6) 

Pressing the 

ENTER 

button again

 

can change the disable/enable state of the sounder outputs 

and the CIE will give a 1 second sound indication.   

7) 

Pressing the 

CANCEL

 button exits the disablement setting status and the 

DISABLE/ENABLE 

LED will be turned off.   

8) 

Exit access level II. 

3.3.3 

Quick Disablement Function – Generally used for group Disablements of Zones or 

Sounder Outputs when the panel is in Alarm mode. 

These  two  buttons 

DISABLE

  and 

DIS/ENABLE  WARNING  SYSTEM

  can  be  used  for  quick 

disablement. The 

DISABLE 

button can disable those zones in a fire condition and 

DIS/ENABLE 

WARNING SYSTEM 

can disable or enable all sounder outputs at the same time.     

Please  note:  The  “

DIS/ENABLE  WARNING  SYSTEM

”  button  can  also  be  used  in  the  normal 

operation mode. 

Содержание GST102A












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды