manualshive.com logo in svg

GST GST102A, Инструкция по установке и эксплуатации

Поделиться
Скачать
GST GST102A Скачать руководство пользователя страница 2

GST102A/GST104A/GST108A/GST116A 
Conventional Fire Alarm Control Panel

   

Installation and Operation Manual 

Page

  I 

 

 

 

QUICK OPERATION GUIDE 

PANEL FAULT 
BUZZER:

 

Press the “SILENCE BUZZER” button to silence the 
panel fault buzzer. 

For any of the below functions you must be in Access Level 2 mode 

ACCESS LEVEL 
2 MODE: 

Insert the 003 key and turn to the “ON” position. 

PANEL ALARM 
BUZZER: 

Press the “SILENCE BUZZER” button to silence the 

panel alarm buzzer. 

WARNING 
SYSTEM 
ACTIVATION: 

Press the “EVAC” button for manual activation of the 

warning system. Alternatively, if an alarm has been 

activated press the “SILENCE/RESOUND ALARM” 

button to silence and reactivate the warning system. 

FIRE MODE 
DISABLING: 

To disable zones in fire mode, press “SILENCE/RESOUND   
ALARM” then “DISABLE” to disable all zones that have   
been activated in fire mode.

 

DISABLING 
ZONES: 

 

Press the “DISABLE/ENABLE” button. 
Use the “SCROLL” button to cycle through to the 

desired zone or sounder output. 
Press the “ENTER” button to save, Panel buzzer will 

sound for 1s to indicate successful setup. 
Press the “SCROLL” button to continue to addition 

zones/sounder outputs. 
Press the “CANCEL” or “DISABLE/ENABLE” to exit 

this menu. 

DISABLING 
WARNING 
SYSTEM: 

Press the “DIS/ENABLE WARNING SYSTEM” button. 

ENABLEMENT: 

Repeat the disablement procedure above. 

PANEL RESET: 

Press the “RESET” button. 

EXIT: 

Turn the 003 key to the “OFF” position and remove 

key. 

Содержание GST102A












































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды