GST GST-IFP8 Скачать руководство пользователя страница 8

Страница: 8 / 66

GST-IFP8 Intelligent Fire Alarm Control Panel

Installation and Operation Manual

Page 2



Nexans NX 200 and 200 Plus (LPCB tested)



Prysmian FP 200 and 200 Gold



Draka Firetuf and Firetuf Plus

And all LPCB approved Fire cables



Recommended Cable Length

≤1000m

2.3.2 RS232 Communication Loop



Connecting with a PC for running graphic monitor system through a DB9 port or

USB port.



Connecting with XS1 of P-9935Modbus Communication Card, Modbus RTU

protocol communication can be executed with the third party Modbus system.



Connecting with computer with graphic monitor center (GMC) system through

REPEATER (A, B) port. It also provides a RS485 port.



Recommended Wiring:



RS232: Standard RS-232 interface. The 2

pin (for sending data), the 3

(for receiving data), and the 5

pin (ground) are connected with PC through

three-core screened cable

(Note: the length of cable should be shorter

than 3m;

the screening

layer and computer’s enclosure should be

earthed).



USB: Standard USB printer cable. The length of cable should be less than 3m.



RS485 Port:

Recommended Wiring (subject to local installation codes):



GST fire cable



Vencroft Gold and Platignum



Nexans NX 200 and 200 Plus (LPCB tested)



Prysmian FP 200 and 200 Gold



Draka Firetuf and Firetuf Plus

And all LPCB approved Fire cables



Recommended Cable Length

≤1000m

2.3.3 CAN Communication Loop (non-loop circuit/loop circuit)



P-9965 CAN Network Card and P-9965A CAN Network Card Loop Type are

optional.



NETWORK

（

non-loop type, even I+, I-

）

：

Communication cable for connecting with

up to 240 network FACPs from GST

（

I+ corresponds to CAN_L, I- corresponds to

CAN_H

）

. CAN_H and CAN_L are connected to CAN_H and CAN_L of the next

FACP.



NETWORK

（

loop type, even I+, I-, O+, O-

）

：

Communication cable for connecting

with up to 100 network FACPs from GST.

（

I+ corresponds to CAN_L2, I-

corresponds to CAN_H2, O+ corresponds to CAN_H1, O- corresponds to

CAN_L1. CAN_H1 and CAN_L1 are to be connected with CAN_H2 and CAN_L2 of

the next FACP; CAN_H2 and CAN_L2 are connected with CAN_H1 and CAN_L1

of the previous FACP.

）



Recommended Wiring (subject to local installation codes):



Vencroft Gold and Platignum

Содержание GST-IFP8



































































Результаты поиска

Содержание GST-IFP8

Отзывы:

GST GST-IFP8, Инструкция по установке и эксплуатации, Страница: 8 / 66

Результаты поиска

Содержание GST-IFP8

Отзывы: