GST GST-IFP8 Скачать руководство пользователя страница 2

Страница: 2 / 66

GST-IFP8 Intelligent Fire Alarm Control Panel

Installation and Operation Manual

Page I

CONTENTS

Installation Precautions ......................................................................................................1

Preface EN 54 Information ..................................................................................................2

Chapter 1 Product Introduction..........................................................................................3

Chapter 2 Technical Specifications ...................................................................................1

2.1 Operating Voltage ........................................................................................................1

2.2 Standby Batteries .........................................................................................................1

2.3 Communication Loop Parameters ...............................................................................1

2.3.1 RS485 Communication Loop ................................................................................1

2.3.2 RS232 Communication Loop ................................................................................2

2.3.3 CAN Communication Loop (non-loop circuit/loop circuit) .....................................2

2.4 Detection Loop Parameters .........................................................................................3

2.5 Input/Output Loop Parameters .....................................................................................3

2.5.1 ALARM ROUTING (+, -) ........................................................................................3

2.5.2 FEED BACK (F1, F2) ............................................................................................3

2.5.3 OUTPUT TO F.P.E. (+, -) .......................................................................................3

2.5.4 OUTPUT TO SOUNDER (+, -) ..............................................................................3

2.5.5 FAULT OUTPUT (NC, COM, NO) .........................................................................4

2.6 Dimensions ...................................................................................................................4

Chapter 3 Construction and Components ........................................................................1

3.1 Exterior and Interior Construction ................................................................................1

3.1.1 Display Area ..........................................................................................................2

3.1.2 Description of LEDs ...............................................................................................2

3.1.3 Description of Keys................................................................................................3

3.1.4 Zone Indication Panel ............................................................................................3

3.2 Components .................................................................................................................4

3.2.1 Standard Components ...........................................................................................4

3.2.2 Optional Components ............................................................................................5

3.3 Periphery Devices ........................................................................................................6

3.3.1 A Series of Intelligent Fire Detectors .....................................................................6

3.3.2 Modules .................................................................................................................6

3.3.3 Loop Isolator ..........................................................................................................6

3.3.4 Manual Call Points .................................................................................................6

3.3.5 Sounder Strobes ....................................................................................................7

3.3.6 Repeater Panel ......................................................................................................7

3.4 Defining Tool .................................................................................................................7

Chapter 4 Installation ..........................................................................................................8

4.1 Component Inspection .................................................................................................8

4.2 Cabinet Installation .......................................................................................................8

4.3 Start-up Check..............................................................................................................9

4.4 External Connection .....................................................................................................9

4.4.1 Mains Connection ..................................................................................................9

4.4.2 Battery Connection ............................................................................................. 10

4.4.3 Field Device Connection .................................................................................... 10

4.5 Connection Inspection and Device Registration ....................................................... 15

4.5.1 Connection Inspection ........................................................................................ 15

Содержание GST-IFP8



































































Результаты поиска

Содержание GST-IFP8

Отзывы:

GST GST-IFP8, Инструкция по установке и эксплуатации, Страница: 2 / 66

Результаты поиска

Содержание GST-IFP8

Отзывы: