GST GST-IFP8 Скачать руководство пользователя страница 16

Страница: 16 / 66

GST-IFP8 Intelligent Fire Alarm Control Panel

Installation and Operation Manual

Page 6

P-9935 Communication card

P-9935 Modbus Communication card

The monitor & control card provides RS232, RS485 or USB port for

communication with PC, so that the FACP can connect with urban fire alarm

and monitor network, or the central monitor and control system in a building for

integrated graphic control.



REPEATER card (RS232/RS485/USB card)

P-9945RP Repeater Card

REPEATER card provides RS485 port for connecting with GST repeater

panels.

There is a decimal rotary switch on each loop board, communication board and

network board, for setting the channel number of the board. The loop board has

dual channels, and after the rotary switch set the number of the first channel, the

second channel will automatically get its number by adding one to the number of

the first. The numbers of the loop board, communication board and network board

can be mixed.

3.3 Periphery Devices

3.3.1 A Series of Intelligent Fire Detectors

GST-IFP8 can connect with a series of fire detectors, such as I-9102, I-9103, and

I-9105R. The detectors mounted in the protected area transmit monitoring message to

the FACP through Class A loop. Every detector has its own address with which the

FACP can monitor the alarm, fault, and normal status of the detectors.

3.3.2 Modules

GST-IFP8 can connect with I-9300 Addressable Input Module and I-9301 Addressable

Single I/O Module. I-9300 module is used for receiving normally open digital signal from

fire protection device and transmitting the signal back to the fire alarm control panel.

I-9301 module is for connecting fire protection devices that need to be controlled by the

FACP, such as smoke valve, fresh air valve, and damper valve. It can also receive

answer signal from these devices.

3.3.3 Loop Isolator

Loop Isolator can remove the shorted part of loop from the whole system to ensure

normal operation of other devices and to ascertain the location of the part in fault. After

the fault is repaired, the loop isolator can automatically reset the removed part into the

system.

3.3.4 Manual Call Points

A series of manual call point (such as I-9202) can be connected to the loop of GST-IFP8.

When fire is confirmed manually, press the glass on the MCP, alarm signal can be sent

to the FACP. After receiving the alarm signal, the FACP will show the number and

location of the MCP, and sound alarm.

Содержание GST-IFP8



































































Результаты поиска

Содержание GST-IFP8

Отзывы:

GST GST-IFP8, Инструкция по установке и эксплуатации, Страница: 16 / 66

Результаты поиска

Содержание GST-IFP8

Отзывы: