GSSI SIR 4000 Скачать руководство пользователя

Страница: 20 / 163

Geophysical Survey Systems, Inc.

SIR® 4000

Manual

MN72-433 Rev F

Battery

Shows the current status of the SIR 4000 battery, and indicates average run time remaining.

AC Power Supply:

>255 minutes (SIR 4000 is plugged into AC power).

Green Battery:

30-255 minutes remaining.

Yellow Battery:

15-29 minutes remaining (Battery status icon will begin to pulse).

Red Battery:

Less than 15 minutes remain. Battery icon will continue to pulse; replace battery.

Storage

Indicates the amount of used memory on the SD card. The SIR 4000 has 32 GB of internal memory.

GPS

The GPS monitor indicates whether or not a GPS is connected and the quality of the GPS signal.

Green GPS Icon:

The GPS is enabled, detected, and the data has an HDOP of 2 or less.

Yellow GPS Icon:

The GPS is enabled, detected, and the data has an HDOP greater than 2.

Red GPS Icon:

The GPS is enabled, but not detected.

Grey GPS Icon:

The GPS is either not enabled in the GPS menu or it is not detected.

2.3: Setup Collect/Playback Screen

The SIR 4000 Setup Screen displays a preview of the data, an Information Bat, Setup Menu, and Toolbar.

Information Bar (top):

An information bar appears at the very top of the screen and is updated based on

whether the SIR 4000 is currently in Collect or Playback Mode.

•

The left-hand side displays the current mode (Distance, Time, Point, or Playback) and file
information (Project Folder – File Name).

•

The middle displays GPS coordinates if the system is configured to collect GPS points.

•

During collection the right-hand side displays either the scan number if in Time or Point data
collection mode or distance if the Collection Mode is set to Distance.

Содержание SIR 4000




































































































































































Результаты поиска

Содержание SIR 4000

Отзывы:

Похожие инструкции для SIR 4000

Бренды по названию

Популярные бренды

GSSI SIR 4000, Руководство пользователя

Результаты поиска

Содержание SIR 4000

Отзывы:

Похожие инструкции для SIR 4000

Бренды по названию

Популярные бренды