Grunbeck WINNI-mat VGX Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 51

background image

Water Softener

WINNI-mat

®

VGX

Order no. 215 188 040-inter Edited by: KONS-pha-rg G:\BA-188040-INTER-VGX.DOC

16

GENO-STOP

®

G 1”

126 875

GENO-STOP

®

for optimum protection from water dam-

age.

The new safety device GENO-STOP

®

provides reliable

and comprehensive protection from water damage. The
GENO-STOP

®

can be equipped with up to 2 wired water

sensors and 5 wireless water sensors.

For additional models, please inquire.

Delivery pump for regeneration water VGX/GSX

188 800

Delivery pump resistant against salt water for draining the
regeneration water in case of drain levels up to 2.5 m. The
pump is activated via the controller.

Drain connection DN 50 according to EN 1717 for
small water softeners

187 840

Connection accessories for DIN-conform waste water
connection DN 50, consisting of siphon, connection nipple
for drain resp. overflow hose and fastening material.

M-Bus measuring transducer D-DAM, complete

To transmit the flow rate and the meter reading as well
as statistical values of the water meter by means of M-
Bus (IEC 870). Furthermore, flow-controlled pulse out-
put, analogue output and relay contact to Grünbeck con-
troller. Dimensions 160 x 240 x 160 mm

115 850

Extension kit for connection hose

187 860

Extension kit for connection hose to extend the length of
the hose to 1.6 m, consisting of:
2 coupling pieces
2 flexible connection hoses

«
...
14
15
16
17
18
...
»

Содержание WINNI-mat VGX




















































Отзывы:

Нет отзывов

Похожие инструкции для WINNI-mat VGX

Бренд: Water Worker Страницы: 24

Бренд: A.O. Smith Страницы: 64

Бренд: A.O. Smith Страницы: 4

Бренд: A.O. Smith Страницы: 4

120 through 250 Series

Бренд: A.O. Smith Страницы: 74

Бренд: A.O. Smith Страницы: 2

Бренд: Takagi Страницы: 60

Бренд: Omnifilter Страницы: 12

Бренд: RainScapes Страницы: 2

Бренд: Redring Страницы: 4

Бренд: OSO Страницы: 44

DHE?18 SLi 25 A

Бренд: STIEBEL ELTRON Страницы: 22

Бренд: Helvex Страницы: 6

Бренд: A.O. Smith Страницы: 44

Бренд: Bradford White Страницы: 40

Бренд: DEMA Страницы: 8

RESIDENTIAL GAS WATER HEATER

Бренд: A.O. Smith Страницы: 36

Бренд: A.O. Smith Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды