Grunbeck WINNI-mat VGX Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 51

background image

Water Softener

WINNI-mat

®

VGX

Order no. 215 188 040-inter Edited by: KONS-pha-rg G:\BA-188040-INTER-VGX.DOC

6

2 | How to use this operation manual

This operation manual is intended for the operators of our systems. It
is divided into several chapters (a letter is assigned to each of them)
which are listed in the “Table of contents” on page 1 in alphabetical
order. In order to find the specific information you are looking for,
check for the corresponding chapter on page 1.

The headers and page numbers with chapter information make it eas-
ier to find your way around in the manual. In case of larger chapters,
first check out page 1 of said chapter (e. g. H-1) where you will find
more information on the contents of this chapter.

3 | General safety information

3.1 Symbols and notes

Important notes in this operation manual are characterised by sym-
bols. Please pay particular attention to these notes in order to ensure
a danger-free, safe and productive system operation.

Danger!

Failure to adhere to these notes will cause serious or life-

threatening injury, extreme damage to property or inadmissible con-
tamination of drinking water.

Warning!

Failure to adhere to these notes may cause injury, damage

to property or contamination of the drinking water.

Attention!

Failure to adhere to these notes may result in damage to

the system or other objects.



Note:

This symbol characterises notes and tips to make your work eas-

ier.

Tasks with this symbol may only be performed by Grünbeck's tech-
nical service or by persons expressly authorised by Grünbeck.

Tasks with this symbol may only be performed by qualified electrical
experts according to the VDE guidelines or according to the guide-
lines of a similar local institution.

Tasks with this symbol may only be performed by water companies
or approved installation companies. In Germany, the installation
company must be registered in a water company installation directory
as per §12(2) AVBWasserV (German Ordinance on General Condi-
tions for the Supply of Water).

3.2 Operating

personnel

Only persons who have read and understood this operation manual
are permitted to work with the system. The safety guidelines are to
be strictly adhered to.

«
...
4
5
6
7
8
...
»

Содержание WINNI-mat VGX




















































Отзывы:

Нет отзывов

Похожие инструкции для WINNI-mat VGX

Бренд: Zilmet Страницы: 10

Бренд: WaterLogic Страницы: 10

Бренд: WaterLogic Страницы: 4

Бренд: WaterCare Страницы: 7

Бренд: Oasis Страницы: 14

Бренд: SureShot Страницы: 36

Бренд: Watex Страницы: 18

Бренд: STIEBEL ELTRON Страницы: 15

Бренд: corob Страницы: 44

Бренд: A.O. Smith Страницы: 48

Бренд: START International Страницы: 2

Symphony Plus 110 Series

Бренд: Follett Страницы: 6

Бренд: Coffee Queen Страницы: 14

The Dispenser Clear Choice Series

Бренд: Better Living Страницы: 2

Бренд: Bobrick Страницы: 2

Бренд: Bobrick Страницы: 3

Бренд: Bobrick Страницы: 3

Бренд: SIMPLEMENTE AGUA Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды