Grunbeck WINNI-mat VGX Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 51

background image

Water Softener

WINNI-mat

®

VGX

Order no. 215 188 040-inter Edited by: KONS-pha-rg G:\BA-188040-INTER-VGX.DOC

37

I

4. Press „Info“ key (3).

The display indicates the regeneration progress and the remain-
ing time required for the step in progress.

5. Press „Info“ key (3).

The display switches to the basic display (time).

2.4

How to release a manual regeneration

The manual regeneration has to be released if



the softener resumes after a longer period of standstill.



maintenance or repair work had been performed.



the raw water quality has changed and the softener does not pro-

duce the desired soft water quality during the whole filter process.



soft water had been withdrawn from the softener during longer

periods of power failure.



Note:

The new inlet water hardness has to be programmed into the

electronics accordingly (refer to chapter F-4, pos. 2.2).

Only in operating mode; time display:

Press „Hand Reg.“ key (2) for at least 10 seconds.

The softening system starts the regeneration. The progress of the re-
generation is indicated by the circle of arrows in the display.

«
...
35
36
37
38
39
...
»

Содержание WINNI-mat VGX




















































Отзывы:

Нет отзывов

Похожие инструкции для WINNI-mat VGX

Бренд: San Jamar Страницы: 2

Бренд: Eccotemp Страницы: 56

Бренд: Rinnai Страницы: 2

EIWH electronicVED pro Series

Бренд: Vaillant Страницы: 12

HOTRUN-VE Series

Бренд: Elwa Страницы: 12

Бренд: Creator Страницы: 12

Бренд: Creator Страницы: 13

Бренд: Creator Страницы: 18

RESIDENTIAL OIL-FIRED WATER HEATER

Бренд: Giant Factories Страницы: 18

Бренд: Bosch Страницы: 154

Бренд: SPT Страницы: 20

Бренд: Manitowoc Страницы: 52

Бренд: Pentair Pool Products Страницы: 22

Posi-Clear PXC-RP100

Бренд: Pentair Pool Products Страницы: 44

Circ-Logic RU80e

Бренд: Rinnai Страницы: 60

Бренд: Rinnai Страницы: 52

Бренд: Rinnai Страницы: 88

Velcon HF Series

Бренд: Parker Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды