Grunbeck WINNI-mat VGX Скачать руководство пользователя страница 40

Страница: 40 / 51

Water Softener

WINNI-mat

VGX

Order no. 215 188 040-inter Edited by: KONS-pha-rg G:\BA-188040-INTER-VGX.DOC

This is what you observe

This is the cause

This is what to do

c) Other malfunctions

Increased hardness in
blending or soft water



Water softener overrun



Water softener does not

have permanent power
supply (coupled with light
switch)

Check socket.



No turbine water meter

pulses to controller

Notify Grünbeck’s technical customer ser-
vice/authorised service company. Check tur-
bine water meter and cable.



Setting of raw water

hardness is too low

Check raw water hardness in electronics unit
and adjust, if necessary.



Other causes



Setting at blending valve

Check inlet resp. soft water hardness. Check
setting of blending valve and adjust, if neces-
sary.



Water supply interrupted Open shut-off valves



Water withdrawal too

high (exceeding peak
flow indicated on type
designation plate)

Reduce water withdrawal



Not enough salt in brine

tank

Check salt level according to level mark and
refill, if necessary.

Resin in outlet pipe

Defective jet system

Notify Grünbeck’s technical customer ser-
vice/authorised service company

Pressure loss too high

Resin is polluted by undis-
solved particles

Notify Grünbeck’s technical customer ser-
vice/authorised service company

Water softener does not
suck brine



Water pressure is too

low

Increase flow pressure to a min. of 2.0 bar



Brine filling orifice

clogged

Clean brine filling orifice - replace



Injector is clogged

Clean injector - replace



Injector sieve is clogged

Clean injector sieve - replace



Brine valve is clogged

Notify Grünbeck’s technical customer ser-
vice/authorised service company. Remove
brine valve and clean

Brine vale regenerates con-
tinuously

Incorrectly adjusted, defec-
tive or short-circuited switch

Notify Grünbeck’s technical customer ser-
vice/authorised service company.

Содержание WINNI-mat VGX




















































Результаты поиска

Содержание WINNI-mat VGX

Отзывы:

Похожие инструкции для WINNI-mat VGX

Бренды по названию

Популярные бренды

Grunbeck WINNI-mat VGX, Руководство по эксплуатации

Результаты поиска

Содержание WINNI-mat VGX

Отзывы:

Похожие инструкции для WINNI-mat VGX

Бренды по названию

Популярные бренды