GREER Company MicroGuard MG510 Скачать руководство пользователя страница 23

Страница: 23 / 76

W450769A 01/14

Menu 02 – Dimensions

This menu is used to enter the physical dimensions of the crane that were previously recorded in
Appendix A.

1. Press the

Menu Up

Menu Down

button until

“02 Dimensions”

appears in the information

window at the right.

2. Press the

02 Dimensions

button to enter the routine.

3. In the routine, press the

Menu Up

Menu Down

buttons to scroll through each item to be

entered. Enter all dimensions in feet and tenths of a foot.

4. Pressing the upper right key adjacent to the item needing a dimension will immediately open the

number entry screen.

5. Use the

and

buttons adjacent to the numerical values at the bottom of the window to scroll

left or right to select the correct number needed for entry.

6. Press the

button to enter the selected digit in between the brackets on the right. Once the

correct number is located between the brackets, press the

button will save and exit to the next

item.

The routine should be continued until all requested information has been entered into the system and
saved.

TEST

SET

TEST

SET

Содержание MicroGuard MG510













































































Результаты поиска

Содержание MicroGuard MG510

Отзывы:

Похожие инструкции для MicroGuard MG510

Бренды по названию

Популярные бренды

GREER Company MicroGuard MG510, Инструкция по установке, калибровке и устранению неисправностей

Результаты поиска

Содержание MicroGuard MG510

Отзывы:

Похожие инструкции для MicroGuard MG510

Бренды по названию

Популярные бренды