GREER Company MicroGuard MG510 Скачать руководство пользователя страница 22

Страница: 22 / 76

W450769A 01/14

Menu 01 – Crane Data

This menu displays the status of the personality.

1. Press the

Menu Up

Menu Down

button until

“01 Crane Data”

appears in the information

window at the right.

2. Press the

button adjacent to

“01 Crane Data”

to enter the routine.

3. If the system has been reset and is functioning correctly the display will read

“Personality is

Good”.

4. If there is no crane data present, or if the system has become corrupt, the display will read

“Personality not in use”

. In this case, proceed with the Crane data reset routine and reset the

data.

5. To reset the data press

01 Crane Data

button and the system will prompt you with

“Yes!

Calibrate!”

6. Press the

Yes

button to complete the crane data reset. The system will prompt you for the

security code. Use the security code used to access the Calibration Menu. Press the

button

to exit the routine.

7. Upon entry of the correct calibration sequence the display will then read

“Calibrating”

Following this operation the screen should now read

“Personality Good”.

TEST

SET

Содержание MicroGuard MG510













































































Результаты поиска

Содержание MicroGuard MG510

Отзывы:

Похожие инструкции для MicroGuard MG510

Бренды по названию

Популярные бренды

GREER Company MicroGuard MG510, Инструкция по установке, калибровке и устранению неисправностей

Результаты поиска

Содержание MicroGuard MG510

Отзывы:

Похожие инструкции для MicroGuard MG510

Бренды по названию

Популярные бренды