background image

Charge batteries in an open, well-ventilated area away
from spark and flames. Unplug charger before connecting
or disconnecting battery to/from the charging port.
Always wear safety glasses and protective clothing/gear.
Use insulated tools.

Sparks can cause a battery gas explosion, which will
result in serious personal injury. Prevent the battery
terminals from touching any metal mower parts when
removing or installing the battery. Do not allow metal
tools to short between the battery terminals and metal
mower parts. Use insulated tools. Always keep protective
battery cover and rear cover in place.

Explosive gases from batteries can cause serious injury,
or death. Poisonous battery fluid contains sulfuric acid;
contact with skin, eyes or clothing can cause severe
chemical burns.

Follow first aid directions for contact with battery fluid.
Get medical attention immediately.

Incorrect battery cable routing could cause damage to the
mower and battery cables. This can cause sparks, which
can cause a battery gas explosion that will result in
serious personal injury.

Do not open or mutilate the battery. Mutilated batteries
can release corrosive electrolytes which can cause
damage to the eyes or skin. It may be toxic if swallowed.

3

SYMBOLS ON THE PRODUCT

Some of the following symbols may be used on this tool.
Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the
tool better and safer.

Symbol

Name

Explanation

V

Volt

Voltage

A

Amperes

Current

Hz

Hertz

Frequency (cycles per sec-
ond)

W

Watt

Power

min

Minutes

Time

/min

Per Minute

Revolutions, strokes, sur-
face speed, orbits etc., per
minute

Direct Current

Type or a characteristic of
current

no

No Load
Speed

Rotational speed, at no load

Safety Alert

Precautions that involve
your safety.

WARNING
--- Wet Con-
ditions

Do not expose the product
to rain or moist conditions.

Symbol

Name

Explanation

Read Opera-
tor’s Manual

To reduce the risk of injury,
user must read and under-
stand operator’s manual be-
fore using this product.

Eye Protec-
tion

Always wear eye protection
with side shields marked to
comply with ANSI Z87.1
when operating this equip-
ment.

DANGER ---
Keep Hands
and Feet
Away

To reduce the risk of injury,
keep hands and feet away
from rotating parts. Do not
operate unless discharge
cover or grass bag is in its
proper place. If damaged,
replace immediately.

DANGER ---
Steep Slope
Hazard

Use extra caution on slopes.
do not mow slopes greater
than 15 degrees.

DANGER ---
Thrown Deb-
ris

Remove objects that can be
thrown by the blade in any
direction. Wear safety
glasses.

DANGER ---
Keep By-
standers Away

Keep all bystanders at least
100 ft. away.

Look around

Always look where you are
going and be aware of your
surroundings.

Keep children
away

Never carry children on the
mower with you.

No Reach

Do not reach hands or feet
under mower deck.

4

RISK LEVELS

The following signal words and meanings are intended to
explain the levels of risk associated with this product.

SYM-

BOL

SIGNAL

MEANING

DANGER

Indicates an imminently haz-
ardous situation,which, if not
avoided, will result in death
or serious injury.

WARNING

Indicates a potentially hazard-
ous situation,which, if not
avoided, could result in death
or serious injury.

6

English

EN

P0802464-00 v1.2

Содержание CZ52R








































Отзывы: