background image

1

DESCRIPTION

1.1

GENERAL INFORMATION

This manual applies to the following Greenworks
Commercial lines:

1.1.1

TO THE NEW OWNER

The purpose of this manual is to assist owners and operators
in maintaining and operating this Greenworks Commercial
mower. Please read the entire manual carefully; the
information and instructions provided can help you achieve
years of dependable machine performance.

It is the owner’s responsibility to make certain that the
operators and mechanics read and understand this manual and
all decals before operating this machine. It is also the owner’s
responsibility to make certain that the operators and
mechanics are qualified and physically able to operate this
equipment. All operators and mechanics must become
familiar with the safe operation of this equipment, its controls
and safety signs.

Never let children or untrained people operate or service this
equipment. Please note that local regulations may restrict the
age of the operator.

1.1.2

USE THIS MANUAL

General operation, adjustment and maintenance guidance is
outlined for both the experienced and novice Greenworks
Commercial Mower user. Operating conditions vary
considerably and cannot all be addressed individually.
Through experience, however, operators should have no
difficulty developing good operating skills suitable to most
conditions.

Directions used in this manual (e.g., "RIGHT" or "LEFT")
refer to directions when either seated on the mower or
standing facing forward, unless otherwise stated.

Photographs and illustrations used were current at the time of
printing, but subsequent production changes may cause your
machine to vary slightly in detail. Greenworks Commercial
Products reserves the right to redesign and change the
machine as deemed necessary, without notification. If a
change has been made to your machine which is not reflected
in this owner’s manual or the parts manual, see your
Greenworks Commercial Products dealer for current
information and parts.

1.1.3

WARRANTY REGISTRATION

The owner must register the unit by filling out the Warranty
Registration Form, provided in the owner’s packet, to validate
warranty protection. As the new equipment owner, you are
expected to see that this is done at the time of delivery. If
using the Warranty Registration Form, it MUST be completed
and signed by the authorized dealer and original purchaser.
Be sure to register the mower plus each attachment that
displays a model and serial identification number plate with
Greenworks Commercial.

 

WARNING

Any unauthorized modification, alteration, or use of non-
approved attachments voids the warranty and releases
Greenworks Commercial from any liability arising from
subsequent use of this equipment.

1.1.4

WARRANTY REGISTRATION

The mower serial number is found on the date label. The
serial number and model are required on the Warranty
Registration Form. They will also ensure that you receive the
correct parts when replacement becomes necessary.

1.1.5

PARTS AND SERVICE

All warranty repair and service must be handled through an
authorized Greenworks Commercial Products dealer.
Arrangements should be made through your local service
center.

1.2

OVERVIEW

 

1

ROPS (Roll Over Protective Structure)

2

Steering control levers

3

Safety belt

4

Left control panel

5

Right control panel

6

Deck

7

Anti-scalp wheels

8

Front wheel

9

Drive wheel

10

Key of battery pack protection

11

Battery pack protection

12

Charging port

13

Discharge chute

2

English

EN

P0802464-00 v1.2

Содержание CZ52R








































Отзывы: