background image

3. Remove the neutral bypass knob from its original location

and install it to the motor (25). Operate one or both of the
knobs on the motor, as needed.

4. Rotate the neutral bypass knobs (26) clockwise to release

drive brakes; counterclockwise to engage.

5. Install the neutral bypass knob(s) (26) back to its/their

original location after completing maintenance.

 

WARNING

Never drive mower with the neutral bypass knob working.
Always install the neutral bypass knob to the original
position before driving! Failure to re-install the knob could
cause serious damage to your mower and void mower
warranty!

 

WARNING

Never pull the neutral bypass lever outside when the
machine is working on the slope!

8

OPERATION

8.1

BEFORE OPERATION

8.1.1

ADJUST THE SEAT

 

WARNING

Make sure seat pan is securely bolted down prior to each
use to prevent seat from moving/tilting in the event of
mower tipping or rollover.

The seat can be adjusted forward and rearward by moving the
latch under the seat. Move the latch to left and pull the seat

where you have the best control of the machine and are the
most comfortable and then tighten the safety belt.

27

8.1.2

ADJUST THE STEERING CONTROL
LEVER

The steering control levers (2) can be adjusted for operator
comfort. By loosening the cap screws (2-1) that attaches the
upper control lever (2-2) to the lower lever (2-3), the upper
control lever can be pivoted to fit the operator’s personal
preference. The steering control levers should be adjusted so
that they align with each other when in the neutral position.

2-2

2-1

2-3

8.1.3

ADJUST THE DECK CUTTING
HEIGHT

 

DANGER

Never attempt to make any adjustments to the mower deck
while the traction drive system is on or with the deck clutch
engaged. Mower blades cannot be seen and are located very
close to deck housing. Fingers and toes can be cut off
instantly.

Deck height is adjustable from 1" - 6" (3.33 cm - 20 cm).
Deck should be raised while mowing is in progress to avoid
stumps, rocks or other obstacle that can be damage mower
deck.

10

English

EN

P0802464-00 v1.2

Содержание CZ52R








































Отзывы: