background image

2 - 6

• Training includes actual operation.

• Clearly understand instructions.

• Be alert! Conditions can change.

NEVER operate unit after or during the use of 
medication, drugs or alcohol. Safe operation requires 
your complete and unimpaired attention at all times.

NEVER allow anyone to operate the unit when their 
alertness or coordination is impaired.

DO NOT operate unit without wearing adequate outer 
garments. Wear adequate safety gear and protective 
gloves. Wear proper footwear to improve footing on 
slippery surfaces.

Protect eyes, face, and head from objects that may be 
thrown from unit. Wear appropriate hearing protection.

Avoid Sharp Edges. Sharp edges can cut. Moving 
parts can cut or amputate fingers or a hand. Wear 
gloves to service unit when handling sharp edges.

ALWAYS keep hands away from any pinch points.

ALWAYS keep hands and feet away from all moving 
parts during operation. Moving parts can cut off body 
parts.

DO NOT touch unit parts which might be hot from 
operation. Allow parts to cool before attempting to 
maintain, adjust, or service.

Keep the operator platform free of dirt, grease, or mud. 
NEVER place feet under the platform.

Do not tie yourself to the unit.

Controls

Come to a complete stop before reversing.

Never jerk the control levers. Always use a steady even 
action to achieve smooth control.

When using attachments, ensure that they are 
attached correctly with latch pins engaged and practice 
the operation before beginning work.

Always be aware of obstructions that may cause injury 
to operator or damage to the unit.

Avoid loss of control or tipping. Do not carry a load with 
the lift arms raised. Always carry load close to ground. 
Do not step off the platform when lift arms are raised.

Always ensure there is ample overhead clearance.

Keep alert with eyes fixed in direction of travel.

Do not travel with the arms in the raised position.

Maintenance

ALWAYS maintain unit in safe operating condition. 
Damaged or worn out muffler can cause fire or 
explosion.

Check the conditions of the unit at the end of each day 
and repair any damage or defects.

ALWAYS block wheels and know all jack stands are 
strong and secure and will hold weight of unit during 
maintenance.

When performing service which requires arms to be 
raised, make sure cylinder lock is in position and 
secure.

Keep nuts and bolts tight and keep equipment in safe 
operating conditions.

Before maintenance, adjustments, or service (except 
where specifically recommended), shut off engine.

Allow hot parts to cool.

Keep unit free of dirt, stones, and other debris. Clean 
up oil or fuel spills.

Storage

DO NOT store unit inside a building with fuel in the fuel 
tank where any ignition sources are present. Allow unit 
to cool completely.

ALWAYS clean unit before extended storage. See 
Engine Manual for proper storage.

Battery

Avoid Electric Shock. DO NOT reverse battery 
connections.

Explosive Gases! Poisonous battery fluid contains 
sulfuric acid and its contact with skin, eyes, or clothing 
can cause severe burns.

No flames. No sparks. No smoking near battery.

Always wear safety glasses and protective gear near 
battery.

DO NOT TIP battery beyond a 45

o

 angle in any 

direction.

ALWAYS KEEP BATTERIES OUT OF REACH of 
children.

Transport

Use extra care when loading or unloading unit onto 
trailer or truck. Secure unit chassis to transport vehicle. 
Always use the tie down lugs provided on each side of 
the unit to secure the unit when transporting by truck or 
trailer.

NEVER secure from rods or linkages that could be 
damaged.

Always use the lifting lug at the top of the unit when 
lifting the unit with an appropriate crane on a 
construction site.

DO NOT transport with attachment in raised position.

Lower attachment when unit is parked or stored unless 
a positive mechanical lock is used.

Attachments and Accessories

Use only attachments or accessories designed for your 
unit.

Содержание 950001



































































Отзывы: