Gravely 950001 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 66

background image

7 - 49

2. Tie Bolts - Remove the three (3) tie bolts which

hold the bank together, then separate the sections.
Remove the four (4) O-ring face seals, these
should be discarded. See below.

3. Valve Front Cap - Remove the two (2) screws

which fasten the front cap to the work station.

4. Front Cap Removal - Pull the lever mechanism

back at the same time and lift the front cap away
from the work section. The lever mechanism will
disengage from the spool. Take care not to loosen
the location dowels.

5. Valve Back Cap - Remove the two (2) screws which

fasten the back cap to the work section and then
remove the back cap. See below.

6. Cushion Spacer - Check the cushion spacer is in

place inside the rear cap. See below.

7. Spool Removal - Grasp the spring end of the spool

and pull with a twisting motion. Tag the spool with
its work section identification number and letter
type (refer to Step 1).

«
...
47
48
49
50
51
...
»

Содержание 950001



































































Отзывы:

Нет отзывов

Похожие инструкции для 950001

Бренд: Case Страницы: 22

Бренд: Takeuchi Страницы: 20

PalletPal Stack-n-Go FPS3000-43 NAS

Бренд: Southworth Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды