Gravely 950001 Скачать руководство пользователя страница 2

Страница: 2 / 66

Section 1 - Introduction . . . . . . . . . . . . . . . . . . 1-3

1.1 The Manual . . . . . . . . . . . . . . . . . . . . . . . . 1-3

1.2 Technical Service Communications . . . . . . 1-3

1.3 Product Registration . . . . . . . . . . . . . . . . . 1-3

1.4 Unauthorized Replacement Parts . . . . . . . 1-3

1.5 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

Section 2 - Safety . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.1 Safety Alerts . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.2 Signal Words . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.3 Notations . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.4 Practices and Laws . . . . . . . . . . . . . . . . . . 2-4

2.5 Required Operator Training . . . . . . . . . . . . 2-4

2.6 Preparation . . . . . . . . . . . . . . . . . . . . . . . . 2-4

2.7 Service Position . . . . . . . . . . . . . . . . . . . . . 2-4

2.8 Cleaning and Storage . . . . . . . . . . . . . . . . 2-4

2.9 Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . 2-5

Section 3 - Specifications . . . . . . . . . . . . . . . . 3-7

Section 4 - General Maintenance &

Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . 4.8

4.1 Controls and Features . . . . . . . . . . . . . . . . 4-8

4.2 Filling The Fuel Tank . . . . . . . . . . . . . . . . . 4-9

4.3 General Lubrication . . . . . . . . . . . . . . . . . . 4-9

4.4 Lubricate Traction Drive Chain. . . . . . . . . 4-10

4.5 Lubricate Rear Hubs . . . . . . . . . . . . . . . . 4-10

4.6 Check Wheel Nuts . . . . . . . . . . . . . . . . . . 4-11

4.7 Grease Chassis . . . . . . . . . . . . . . . . . . . . 4-11

4.8 Check Engine Oil Level-Gasoline . . . . . . 4-12

4.9 Check Engine Oil Level-Diesel. . . . . . . . . 4-12

4.10 Change Engine Oil- Gasoline . . . . . . . . 4-12

4.11 Change Engine Oil- Diesel . . . . . . . . . . 4-13

4.12 Change Engine Oil Filter . . . . . . . . . . . . 4-13

4.13 Checking Engine Cooling. . . . . . . . . . . . 4-14

4.14 Check Radiator Hoses & Clamps-Diesel 4-15

4.15 Service Air Cleaner-Gasoline . . . . . . . . 4-15

4.16 Service Air Cleaner- Diesel . . . . . . . . . . 4-15

4.17 Checking Tire Pressure . . . . . . . . . . . . . 4-16

4.18 Check Hydraulic Fluid Level. . . . . . . . . . 4-16

4.19 Change Hydraulic Fluid . . . . . . . . . . . . . 4-16

4.20 Change Hydraulic Filters . . . . . . . . . . . . 4-17

4.21 Check Hydraulic Lines . . . . . . . . . . . . . . 4-17

4.22 Check Traction Drive Chain Tension . . . 4-18

4.23 Check Battery Electrolyte . . . . . . . . . . . 4-19

4.24 Charge Battery. . . . . . . . . . . . . . . . . . . . 4-20

4.25 Replacing Fuel Filter- Gasoline . . . . . . . 4-20

4.26 Clean Fuel Filter-Diesel . . . . . . . . . . . . . 4-20

4.27 Adjust Fan Belt- Diesel . . . . . . . . . . . . . 4-21

Section 5 - Engine . . . . . . . . . . . . . . . . . . . . . . 5-22

5.1 Engine Troubleshooting . . . . . . . . . . . . . . 5-22

5.2 Gasoline Engine Removal . . . . . . . . . . . . 5-23

5.3 Gasoline Engine Installation . . . . . . . . . . 5-23

5.4 Diesel Engine. . . . . . . . . . . . . . . . . . . . . . 5-23

5.5 Diesel Engine Removal . . . . . . . . . . . . . . 5-25

5.6 Diesel Engine Installation. . . . . . . . . . . . . 5-26

Section 6 - Drive Train . . . . . . . . . . . . . . . . . . 6-27

6.1 Bell Housing & Coupling . . . . . . . . . . . . . 6-27

6.2 Removal Of The Hydraulic Pump Bell Housing

And Coupling . . . . . . . . . . . . . . . . . . . . . . . . . 6-27

6.3 Pump To Coupling Reassembly . . . . . . . . 6-29

6.4 Hydraulic Pump Removal. . . . . . . . . . . . . 6-30

6.5 Pump Reassembly . . . . . . . . . . . . . . . . . . 6-32

6.6 Drive Motor . . . . . . . . . . . . . . . . . . . . . . . 6-33

6.7 Final Drive Train . . . . . . . . . . . . . . . . . . . . 6-38

Section 7 - Hydraulic System. . . . . . . . . . . . . 7-41

7.1 General Description . . . . . . . . . . . . . . . . . 7-41

7.2 Stand-By Mode (Neutral) . . . . . . . . . . . . . 7-42

7.3 Crowd Function-Bucket Tilt Down . . . . . . 7-43

7.4 Travel Forward Function . . . . . . . . . . . . . . 7-44

7.5 Travel Function - Rotate . . . . . . . . . . . . . . 7-45

7.6 Lift Function - Lift Arms Raise . . . . . . . . . 7-46

7.7 Lift Function- Lift Arms Lower . . . . . . . . . 7-47

7.8 Valve Bank Disassembly . . . . . . . . . . . . . 7-48

7.9 Trenching Valve . . . . . . . . . . . . . . . . . . . . 7-52

7.10 Hydraulic Cylinders . . . . . . . . . . . . . . . . 7-57

7.11 Overcenter Valve . . . . . . . . . . . . . . . . . . 7-62

7.12 Quick Disconnect Couplings . . . . . . . . . 7-63

Section 8 - Fuel System . . . . . . . . . . . . . . . . . 8-64

TABLE OF CONTENTS

Содержание 950001



































































Результаты поиска

Содержание 950001

Отзывы:

Похожие инструкции для 950001

Бренды по названию

Популярные бренды

Gravely 950001, Руководство по обслуживанию

Результаты поиска

Содержание 950001

Отзывы:

Похожие инструкции для 950001

Бренды по названию

Популярные бренды