background image

1 - 3

1.1  THE MANUAL

It is the purpose of this manual to provide complete 
instructions for service, maintenance, disassembly, 
repair, and installation of the mechanical components 
for the Skidster 200.

Dealer trained service personnel should use this 
manual as a supplement to and reminder of the training 
sessions conducted by the company.

Read all information for servicing a part of system 
before repair work is started to avoid needless 
disassembly.

Operation

Before operation of the unit, carefully and completely 
read manuals supplied with the unit. The contents will 
provide you with an understanding of safety 
instructions and controls during normal operation and 
maintenance.

Safety Messages

For your safety and the safety of others always read, 
understand, and follow all DANGER, WARNING, and 
CAUTION messages found in manuals and on safety 
decals.

Directional Reference

All reference to left, right, front, or rear are given from 
the operator in the operator position and facing the 
direction of forward travel.

Notation Definitions

NOTE: General reference information for proper 
operation and maintenance practices.

IMPORTANT: Specific procedures or information 
required to prevent damage to the unit or the 
attachment.

1.2  TECHNICAL SERVICE 
COMMUNICATIONS

Ariens Technical Service communicates information to 
the field using Service Letters, Service Bulletins, 
Product Notices, and Campaigns. Each communication 
signifies a type of information and priority. The dealer is 
responsible to carry out the directive provided in the 
communication. The types of communication are:

Service Letter

General technical information for the dealer. Technical 
information on how to service the product and product 
improvements.

Service Bulletin

Notification to update products to resolve certain 
issues or a notification of a policy change.

Product Notices

Notification of limited product located in a certain 
region. This is a limited distribution to only those who 
received the product involved.

Campaigns

Notification of a safety related issue. All product must 
be updated and are tracked by the factory until all units 
are corrected.

1.3  PRODUCT REGISTRATION

A warranty registration card must be filled out, signed, 
and returned at the time of purchse. This card activates 
the warranty. Claims meeting requirements during 
limited warranty period will be honored.

1.4  UNAUTHORIZED REPLACEMENT 
PARTS

Use only Gravely replacement parts. The replacement 
of any part on this vehicle with anything other than a 
Gravely authorized replacement part may adversely 
affect the performance, durability, or safety of this unit 
and may void the warranty. Gravely disclaims liability 
for any claims or damages, whether warranty, property 
damage, personal injury, or death arising out of the use 
of unauthorized replacement parts.

1.5  DISCLAIMER

Gravely reserves the right to discontinue, make 
changes to, and add improvements upon its products 
at any time without public notice or obligation. The 
descriptions and specifications contained in this 
manual were in effect at printing. Equipment described 
within this manual may be optional. Some illustrations 
may not be applicable to your unit.

SECTION 1 - INTRODUCTION

Содержание 950001



































































Отзывы:

Похожие инструкции для 950001