GRAUPNER mz-32 HoTT, Руководство пользователя

Страница: 30 / 48

30 / 48 S1024.mz32_V1.7_sh_en
Assign Digital Switches to a widget step-by-step
1. Switch to the submenu “Digital Switch”.
2. Tap on the
Įƌ st “Act” icon to ĂĐƟǀĂ te the Digital Switch and select
the desired mode (On/O ī͕ P ƵůƐĞŽƌ&ůĂƐŚͿ͘
3. Connect for example a servo to the channel you designated as
Digital Switch.
4. Go to the Home page and select an empty ĚĞĐŬ or available ďůŽĐŬ
an bring up the Widget Editor.
5. Select the “Digital Switch” widget and tap on DS1 which is the
widget we assigned in the previous step.
6. Test the ŽƉĞƌĂƟŽŶ by tapping on the bu Ʃ on. You can change its
behavior in the “Digital Switch” submenu.
Se ƫŶŐ control and mixer characteris ƟĐƐ
Both the control characteris ƟĐƐŝŶƚŚĞƐƵďŵĞŶƵ „control se ƫŶ g“ of
the basic menu as well as virtually all mixer characteris ƟĐƐ are set
essen ƟĂůůLJ according to the same principles. The corresponding pro-
cedure is shown below with reference to the thro ƩůĞĐƵ rve.
However, the se ƫŶŐƐ shown have a purely demonstra Ɵ ve character
and in no way correspond to real thro ƩůĞĐŚĂ racteris ƟĐƐ͊
Select characteris ƟĐĐƵ rve step-by-step
1. Enter the desired submenu.
Here is an example of the submenu “control se ƫŶŐ ”.
2. In the desired line touch the symbol
…
in the “Detail” column.
Here is an example of the con ƚƌŽůĨƵŶĐƟŽŶ “Thro ƩůĞ ”.
The display sho ǁŶŽŶƚŚĞůĞŌǁŝůůďĞĚŝƐƉůĂLJĞĚ͘
3. Touch the “Other ͟ĮĞůĚŝŶƚŚĞƵƉƉĞƌƌŝŐ ht corner.
The display sho ǁŶŽŶƚŚĞůĞŌǁŝůůďĞĚŝƐƉůĂLJĞĚ͘
4. Touch the brigh ƚƐĞůĞĐƟŽŶĮĞůĚ to the right of “Curve type”.
In rot ĂƟŽŶ proc ĞĚƵƌĞ͕ select the desired curve type or the desired
control characteris ƟĐ͘dŚĞĐŚŽŝ ces are:
-
A linear characteris ƟĐ without points between the endpoints.
This characteris ƟĐ corresponds to the standard se ƫŶŐ͘
-
A linear characteris ƟĐ with 5 points evenly distributed between
the endpoints.
This characteris
ƟĐ is to be selected as the basis of non-linear
characteris ƟĐƐ͘
-
A horizontal curve with a single point in the middle of the con-
trol.