GRAUPNER mz-32 HoTT, Руководство пользователя

Страница: 29 / 48

29 / 48 S1024.mz32_V1.7_sh_en
Assign digital switches in “RF Set” step-by-step
1. Bind the receiver you wish to assign to a digital switch and verify
no other rec ĞŝǀĞƌŝƐĂĐƟǀĞ͘
2. Switch to the submenu “RF Set” of the basic menu.
3. Select the receiver you would li
Ŭ e to use by tapping on the blue
ĮĞůĚǁŚŝĐŚŝƐƚŚĞĂĐƟǀĞƌĞ ceiver.
4. By tapping the blue ĮĞůĚ with the receiver type a ƐĞůĞĐƟŽŶ win-
dow appears.
5. Tap the channel number for which you would li Ŭ e to assign a dig-
ital switch.
The tapped
ĮĞůĚ is displayed inverted and a control panel is dis-
played at the bo ƩŽŵ;ƐĞĞůĞŌĮŐƵƌĞͿ͘
6. Use the “ ”- or “ ” bu Ʃ ons to assign the desired Digital Switch
to the selected receiver channel.
-
In the illus ƚƌĂƟŽŶ on the ůĞŌ͕ for ex ĂŵƉůĞ͕ the digital switch
“D1” is selected at the receiver c ŽŶŶĞĐƟŽŶ 14 of the receiver
(the bound receiver is a 'ZͲϯϮ͕ 16 channel receiver. You can
use any HoTT rec ĞŝǀĞƌͿ͘ Touching the ĐŚĞĐŬ ŵĂƌŬ in the bot-
tom right c ŽŶĮƌŵƐƚŚĞƐĞůĞĐƟŽŶ͘
7. If necessary proceed iden Ɵ cally with other receiver c ŽŶŶĞĐƟŽŶƐ͘
8. By tapping on the symbol pulse ( Ϳ you can change to level ( Ϳ
ĂŶĚďĂĐŬ to pulse again.
-
When the symbol pulse ( Ϳ is select ĞĚ͕ servo pulses are out-
put to the corresponding channel output.
-
When the symbol level ( Ϳ is select ĞĚ͕ the output of the cor-
responding channel is switched to high or low.
Notes
ͻ Switching to level allows the direct c ŽŶŶĞĐƟŽŶ of transistors
Žƌ>Ɛ to the receiver output via a series resistor.
ͻ In Graupner receivers GR-12 ;ηϯϯϱϬϲͿ͕ GR-16 ;ηϯϯϱϬϴͿ͕
GR-24 ;ηϯϯϱϭϮͿ͕ 'ZͲϯϮ ;ηϯϯϱϭϲͿ and GR-24 PRO ;ηϯϯϱϴϯͿ as
well as 'ZͲϭϲ> ;η^ϭϬϮϭͿ͕ 'ZͲϮϰ> ;η^ϭϬϮϮͿ and 'ZͲϯϮ>
;η^ϭϬϮϯͿ series resistors are allready installed and >Ɛ can
be connected directly between the orange servo pulse wire
and the brown or black “-” wire.
9. Touching “OK” completes the process. Touching “Reset” resets
the receiver to the default se ƫŶŐƐ͘
In both c ĂƐĞƐ͕ the display will be closed and you will return to the
“RF Set” menu.