GRAUPNER mx-20 Hott, Руководство по программированию

Страница: 124 / 296

124 Detail program description - Control adjust
SEL
0%
0%
0%
C1
C2
C3
––– C4
CONTROL SWITCH
0%
STO
–––
–––
––– Ct6
Resetting a control switch back to "free"
To reset a control switch back to "free", make sure the
display is as below …
SEL
+75%
0%
0%
G1
G2
C3
––– C4
CONTROL SWITCH
Gb1
Gb1 –75%
STO
–––
–––
–––
Move desired
control adj.
… and then press the

or

keys on the right
touch pad ( CLEAR ) briefl y to erase the transmitter
control assignment.
Defi ning the switching point
Using the arrow key

on the left or right touch pad,
move the marker frame into the STO (i.e. the STOre)
column.
Move the selected transmitter control to the position at
which the switching point – i. e. the switch between OFF/
ON – should trigger and briefl y tap the center
SET key
on the right touch pad. The current position is displayed,
for example "+85%":
SEL
0%
0%
0%
C1
C2
C3
––– C4
CONTROL SWITCH
+85%
STO
–––
–––
––– Ct6
The switching point can be altered at any time by
tapping the center
SET key on the right touch pad again.
Note:
Do not, however, set a switching point at a transmitter
control's travel end-point, since this makes reliable
switching impossible. Where a 3-stage switch (CTRL 9
and 10) is used to operate a control switch you should
therefore program the switching point beforehand using
one of the proportional rotary controls (CTRL 6 to 8):
First, assign the corresponding proportional control in
the 2nd column and set the switching point in such a
way that will ensure the subsequent confi guration for
the 3-stage switch will reliably exceed this value. If you
do not, the switching function will be unreliable, since
the control switch triggers only if a value unambiguously
fails to meet or exceeds the value set! To complete the
procedure, de-assign the transmitter control and then
assign the 3-stage switch.
Setting the switching direction
The switching direction of the control switch is changed
as required in the 4th column. Using the arrow key

on
the left or right touch pad, move the marker frame into
the
SEL (i.e. the SELect) column. After briefl y tapping
the center SET key on the right touch pad, you can then
use the arrow keys on the left or right touch pad to set
the switching direction from "normal" to "reversed" and
vice versa:
SEL
0%
0%
0%
C1
C2
C3
––– C4
CONTROL SWITCH
+85%
STO
–––
–––
––– Ct6
SEL
0%
0%
0%
C1
C2
C3
––– C4
CONTROL SWITCH
+85%
STO
–––
–––
––– Ct6
Tapping the

or

keys on the right touch pad at
the same time ( CLEAR ) will reset the switching direction
to "=>".
The current switch position of the control switch is
displayed in the leftmost column by the switch icon next
to the number of the control switch.
Notes:
In this example, control switch "C1" remains open •
while transmitter control 6 (the throttle limiter for
a heli) is at less than +85% of full travel. It closes
once the switching point is exceeded, i.e. by a value
b85% and the upper travel end-point.
In the above example with the switching direction
•
reversed, control switch "C1" remains closed while
the transmitter control is at less than +85% of full
travel. As soon as the switching point is exceeded –
in this example, by a value b85% and the
upper travel end-point – "C3" opens.