GRAUPNER mx-20 Hott, Руководство по программированию

Страница: 77 / 296

77 Detail program description - Base setup model | Helicopter
second bound receiver) will begin with 13.
RECEIVER CH – BIND2
In Ch12
Out Ch13
In Ch12 Out Ch14
In Ch12
Out Ch15
In Ch12 Out Ch16
After selection of the desired output with the arrow keys
of the left and right touch pad, the corresponding input
fi eld will be framed. Press the center
SET button in the
right touch pad The current setting will be displayed
in inverse video. Now select the desired input channel
with the arrow keys of the right touch pad. For example,
appropriate for the above example with roll servos:
In Ch 2 Out Ch14
In Ch12 Out Ch15
In Ch12 Out Ch16
RECEIVER CH – BIND1
In Ch 1
Out Ch13
Notice:
The number of lines available (outputs) corresponds to
the maximum number of servos which can be connected
to receiver 2 and their numbering is dependent on the
maximum number of servos which can be connected to
receiver 1.
RF transmit
This menu line provides an option for manually
switching the transmitter's RF transmission on and off
to specifi c models while the transmitter is in operation.
For example, to save power while a model is being
programmed. If this line option was set to OFF, it
will be canceled (i.e. set to ON) the next time the
transmitter is switched on.
If necessary, use the

arrow keys of the left or right
touch pad to reach the "RF transmit " line then activate
the option by briefl y pressing the center
SET button in
the right touch pad.
SEL
R12 R08
1
OFF
bind
Stick mode
RF BIND
BASIC SETTINGS, MODEL
Rcv Ch Map
bind
RF transmit
The right arrow keys can now be used to choose
between
OFF and ON . Again pressing the center SET
button in the right touch pad will complete the entry.
Range test
The built-in range test reduces transmission power to an
extent that a function test can be carried out even within
a distance of up to about 50 m.
Perform the range test on the
Graupner HoTT system
according to the following instructions. If necessary,
have someone assist you in carrying out the range test.
Preferably the receiver already bound to the 1.
transmitter should be installed into the model in its
intended position.
Switch remote control on and wait for the receiver's
2.
green LED to light up. Now servo movements can be
observed.
Place the model on a level surface (pavement,
3.
low-cut grass or bare ground) such that receiver
antennas are at least 15 cm above ground level. It
may be necessary to put something under the model
to raise it up enough for this.
Hold the transmitter at hip level and at some distance
4.
from one's body. Do not point the antenna directly at
the model but rather turn and/or kink the antenna's
end so that it is oriented vertically during the test.
If necessary, use the
5.

arrow keys of the left or
right touch pad to reach the "RF Range Test" line in
the menu then start range test mode by pressing the
center
SET button in the right touch pad.
SEL
RF Range Test 99sec
R12 R08
OFF
bind RF BIND
BASIC SETTINGS, MODEL
Rcv Ch Map
bind
RF transmit
When the range test is activated, the transmitter's
output power will be signifi cantly reduced and the
blue LED on the antenna's socket will begin to
blink. At the same time, the timer display in the
transmitter's screen will start counting down and
every 5 seconds a two-frequency tone will sound.
STARLET
#02
2:22h
Stop
Flt
«nor mal »
K78
0:00
0:00
5.5V
5.2V
M
HoTT
TEST 76s
Five seconds prior to the end of the range test a
three-frequency tone will sound once every second.
After expiration of the range test's 99th second the
transmitter will again be switched to full output power