GRAUPNER HoTT MC-16 Series, Руководство по программированию

Страница: 320 / 332

320 Programming examples - Helicopter models
Note:
More more information about the setting of this
“emergency shutoff”, see further in this section.
Another tip:
Make a habit of giving all switches a common switch-
on direction; then a quick glance over the transmitter
prior to the flight should suffice – all switches off.
Setting options for the “Autorotation C1 position”,
“Motor stop” and “Stick warning” are not yet of par-
ticular interest …
… and you should only leave or set the “Auto timer
reset” line to “yes” if you actually want the timers to
be reset to the appropriate initial value every time you
switch the transmitter on.
Additional settings specific to helicopters are made in
the menu …
»Helicopter type« (page 108)
In the “Swashplate type” line, select control for
swashplate or pitch function. In this example:
“3Sv(2rol)”.
The “Linearis. swashpl.” line is not yet of interest.
In the “Rotor direction” line, it is established whether
the rotor – as viewed from above – turns to the right
(clockwise) or left (counter-clockwise). In other words,
whether it rotates counterclockwise or clockwise. In
this example “right”.
Check the default for “Pitch min”, which was adopted
from »Basic settings«, to confirm that the entry
“front” or “rear” is in keeping with personal prefer-
ences or should be changed:
3Sv(2rol)
SEL
Linear. swashpl.
Swashplate
no
Rotor direct right
Heli type
Pitch min. back
1
n/a bind
ST R ET
Rcv Ch Map R12 n/a
HoTT
Mod.name
Stick mode
module
Base setup model
… which must be assembled from characters avai-
lable on the second page of the “Model name” line:
! " # $ % & ’ ( ) � + , – . / 0 1 2 3
4 5 6 7 8 9 : ;
Mod Name STAR L
F G H I J K L M N O P Q R S T U V W X
Y Z [ ¥ ] ^ _ ` a b c d e f g h i j k
? @ A B C D E
After entering the “Model name”, the settings adopt-
ed from »Basic settings« for “Stick mode” and “DSC
Output” are to be checked and changed as neces-
sary for the given memory location.
Another option is to be activated in the “Autorotation”
line. Even if you are not an advanced pilot, the autoro-
tation switch should at least be set as an emergency
shutoff switch for the motor.
Do this by selecting the “Autorotation” line with a
brief tap on the center
SET key of the right touch
pad, activate the switch assignment, assign a 2-way
switch, e. g. “7”, and put it in its “ON” position:
99sec
PPM10
7I
ON
DSC Output
Autorotation
RF transmit
Base setup model
RF Range Test
The selected switch should be in a location on the
transmitter which is easily within reach – without let-
ting loose of a stick – e. g. above the pitch stick.
“Expo throttle lim.” in the bottom line of this display,
are currently of no interest.
By now, the servos should be plugged into the recei-
ver in the intended sequence:
Receiver power supply
Free or aux. function
Free or aux. function
Tail rotor servo (gyro system)
Roll 1 servo
Pitch-axis 1 servo
Free or speed governor or aux. function
Receiver power supply
Collective pitch or roll 2 or
Pitch-axis 2 servo
Free or aux. function
Throttle servo or speed controller
Gyro gain
Free or aux. function
Free or aux. function
Note:
Please note that on the newer Graupner-
mc
- and
mx
- remote control systems, the first pitch servo and
the throttle servo are swapped in comparison to some
older systems.
Mix ratios and mix directions for swashplate pitch, roll
and nick servos are already pre-adjusted to +61 % in
the menu …
»Swashplate mixer« (page 220)
Swashplate mixer
Pitch
Roll
Nick
+61%
+61%
+61%
SEL
If the swashplate mixer should not follow stick move-
ments properly, first change the mixing directions
from “+” to “-” before changing servo directions in the