Gotting HG G-19600ZA Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 38

background image

Preliminary Device Description HG G-19600ZA | English, Revision 02 | Date: 13.03.2018

5

About this Document – Chapter 1

1

About this Document

1.1 Function

This device description contains information regarding the correct mounting, electric instal-
lation, commissioning and maintenance of the magnet sensor HG G-19600ZA for the tech-
nical personnel of a manufacturer who wants to integrate the magnet sensor into an auto-
mated guided vehicle (AGV).

This device description does not contain information regarding the usage of the superordi-
nate system, e.g. the automated guided vehicle (AGV). For this information consult the doc-
umentation of the vehicle manufacturer resp. the operator of a facility.

This device description applies to devices with firmware version V0.40 and higher (see Fig-
ure 15 on page 23 on how to detect which firmware version your device has).

1.2 Symbols

The following symbols and formatting are used in Götting documentations:

Note

Indicates technical information that should be followed when using the device.

ATTENTION!

Indicates dangers that may lead to damages or the destruction of the device.

BEWARE!

Indicates dangers that may lead to injuries or severe damage of property.

WARNING!

Indicates dangers that may lead to injuries, potentially with loss of life, or severe damage of
property.

Tip

Indicates information that makes handling of the device easier.

«
...
3
4
5
6
7
...
»

Содержание HG G-19600ZA







































Отзывы:

Нет отзывов

Похожие инструкции для HG G-19600ZA

Бренд: cam Страницы: 2

WV7220D - CCTV ACCESSORIES

Бренд: Panasonic Страницы: 10

WV-NS202 - i-Pro Network Camera

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 3

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 4

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 32

Бренд: Panasonic Страницы: 19

Бренд: Panasonic Страницы: 59

Бренд: Zacuto Страницы: 4

Бренд: i-PRO Страницы: 2

Бренд: Garmin Страницы: 22

Бренд: Hach Страницы: 44

Бренд: Habasit Страницы: 14

KOOLZONE SAC-1800

Бренд: UNINEX Страницы: 5

Бренд: Vaisala Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды