manualshive.com logo in svg

Gotting HG G-19600ZA, Руководство пользователя

Поделиться
Скачать
Gotting HG G-19600ZA Скачать руководство пользователя страница 13

Preliminary Device Description HG G-19600ZA | English, Revision 02 | Date: 13.03.2018

13

Mounting – Chapter 3

Figure 7

Possible mounting pos. for the magnet sensor when using an optional distance piece

Tip

If the magnet sensor has to be mounted side-inverted (aka backwards) the output voltages 
for the left and right deviations may be interchanged compared to what the vehicle control 
expects. In this case the output voltage AOUT1 can be inverted inside the sensor, see 6.4.2

 

on page 26.

3.2.3 Connection Cable (assembled on one side)

Connect the sensor to the vehicle control. For this the connectors ST 1 and ST 2 are used. 
The assignment of the pins is shown in section 5.2 on page 20. The following optional cable

 

extensions can be used.

Order no.

Description

HW CAB00001

Cable PUR, 5m with one M12 angle coupling, 5 pin, A coded,

one end open

HW CAB00007

Cable PUR, 5m with M12 angle coupling, 8 pin, A coded,

one end open

Table 2

Accessories / cable extensions

Magnet tape

Roadway

Optional

Magnet sensor

Vehicle body

Direction of travel

distance piece
(material non
ferro-magnetic)

Содержание HG G-19600ZA







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды