Gotting HG G-19600ZA Скачать руководство пользователя страница 30

Страница: 30 / 38

Preliminary Device Description HG G-19600ZA | English, Revision 02 | Date: 13.03.2018

Chapter 6 – Software

6.4.6 Software Update (Firmware)

Directly after switching the supply voltage on the following message appears in the termi-
nal program.

Figure 23

Menu software update

In order to start a software update press the key



within 5 seconds.

Figure 24

Transfer of a firmware update

At this point the transfer can be started, the protocol has to be

Y-Modem

. If the transmission

is successful the following message appears. Press any key to quit, afterwards the sensor
switches to normal operation mode.

Figure 25

Finishing a software update

+--------------------------------------------------------------------+
|           |
| HG 19600 Bootloader V1.1       |
|           |
+--------------------------------------------------------------------+

Serialnumber: 999999

Press F to Upload new Firmware..................

Serialnumber: 999999

Press F to Upload new Firmware.....
Waiting for the file to be sent (YModem)... (press 'a' to abort)

Serialnumber: 999999

Press F to Upload new Firmware.............
Waiting for the file to be sent (YModem)... (press 'a' to abort)
C

Programming Completed Successfully!
--------------------------------
Name: HG19600_user.bin
Size: 30664 Bytes
-------------------

Press any key...

Содержание HG G-19600ZA







































Результаты поиска

Содержание HG G-19600ZA

Отзывы:

Похожие инструкции для HG G-19600ZA

Бренды по названию

Популярные бренды

Gotting HG G-19600ZA, Руководство пользователя

Результаты поиска

Содержание HG G-19600ZA

Отзывы:

Похожие инструкции для HG G-19600ZA

Бренды по названию

Популярные бренды