Goldacres Super Cruiser G8, Руководство оператора, Страница: 121 / 210

Chapter 9 - Boom - 117 G8 Super Cruiser Operator’s Manual MY19 - REV 0
Boom Adjustment - 36-42 m
90°
89°
Side view
NOTE: Torque 12 x Bolts to 37 lbft (50Nm)
Use Loctite 243 (blue)
F
E
REVISIONS
REV DESCRIPTION DATE / INITIAL ECN
01 Replaced U bolts with clamp blocks 2/02/18 CT 954
02 ADD RHS SPACER PLATES 14/09/18 CT 1016
A3
SHEET 2 OF 2
DRAWING NUMBER:
TITLE:
MATERIAL
:
DRAWN BY:
GA4907345 with Clamp
Support Plate
ALUMINIUM BOOM WING ASSEMBLY, 36M,
MY15
C.TURNER
COENTURNER
MODEL EDITED BY:
31/07/2003
THIS DRAWING REMAINS THE PROPERTY
OF GOLDACRES TRADING PTY LTD AND IS
SUBJECT OF COPYRIGHT
SURFACE FINISH:
WEIGHT: DRAWING EDITED BY:
13/12/2018
REV
02
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETRES
SHEET
1-3 MORANG CR. MITCHELL PARK.
VICTORIA 3355 AUSTRALIA
PH: 03 5342 6399
DEBURR AND BREAK
SHARP EDGES
COENTURNER
14/12/2018
DRAWING CHECKED BY:
KG
DO NOT SCALE DRAWING
UNLESS OTHERWISE SPECIFIED
0. ± 1 ANGULAR ± 0.50°
0.0 ± 0.5
0.00 ± 0.25
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
90°
89°
Side view
NOTE: Torque 12 x Bolts to 37 lbft (50Nm)
Use Loctite 243 (blue)
F
E
REVISIONS
REV DESCRIPTION DATE / INITIAL ECN
01 Replaced U bolts with clamp blocks 2/02/18 CT 954
02 ADD RHS SPACER PLATES 14/09/18 CT 1016
A3
SHEET 2 OF 2
DRAWING NUMBER:
TITLE:
MATERIAL
:
DRAWN BY:
GA4907345 with Clamp
Support Plate
ALUMINIUM BOOM WING ASSEMBLY, 36M,
MY15
C.TURNER
COENTURNER
MODEL EDITED BY:
31/07/2003
THIS DRAWING REMAINS THE PROPERTY
OF GOLDACRES TRADING PTY LTD AND IS
SUBJECT OF COPYRIGHT
SURFACE FINISH:
WEIGHT: DRAWING EDITED BY:
13/12/2018
REV
02
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETRES
SHEET
1-3 MORANG CR. MITCHELL PARK.
VICTORIA 3355 AUSTRALIA
PH: 03 5342 6399
DEBURR AND BREAK
SHARP EDGES
COENTURNER
14/12/2018
DRAWING CHECKED BY:
KG
DO NOT SCALE DRAWING
UNLESS OTHERWISE SPECIFIED
0. ± 1 ANGULAR ± 0.50°
0.0 ± 0.5
0.00 ± 0.25
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
Aluminium Outer Wing
When the booms are fitted at the factory, they
are made level or slightly increasing in height from
the centre section. Under working conditions the
aluminium outer booms will need to be checked
at every 50 hour intervals as per the Maintenance
Schedule.
If the aluminium outer boom is not level in the
working position, then a likely cause of this may be
sagging or stretching.
Shims may need to be placed or removed at the fold
hinge bearing blocks to get the booms level. Refer to
Vertical boom alignment - working position.
If the aluminium top cords around the bolts show
any signs of movement, then the bolts will need to
be tightened.
Adjustments should be performed with the boom
in the lowered working position. Check that the end
plate to cords are at 89-90 degrees to each other.
If the angle is too large then the wing is sagging. Set
the angle correctly using the top bolts and re-tighten
to 37 lbft / 50 Nm. The U-bolts should be done up
just tightly enough to hold the position set by the
upper chord bolts. Overtightening the U-bolts on
the diagonal chord will bend and damage the boom.
Above: Cross section of top chord mounting.
Note orientation of spacer inserts.
90°
89°
Side view
NOTE: Torque 12 x Bolts to 37 lbft (50Nm)
Use Loctite 243 (blue)
F
E
REVISIONS
REV DESCRIPTION DATE / INITIAL ECN
01 Replaced U bolts with clamp blocks 2/02/18 CT 954
02 ADD RHS SPACER PLATES 14/09/18 CT 1016
A3
SHEET 2 OF 2
DRAWING NUMBER:
TITLE:
MATERIAL
:
DRAWN BY:
GA4907345 with Clamp
Support Plate
ALUMINIUM BOOM WING ASSEMBLY, 36M,
MY15
C.TURNER
COENTURNER
MODEL EDITED BY:
31/07/2003
THIS DRAWING REMAINS THE PROPERTY
OF GOLDACRES TRADING PTY LTD AND IS
SUBJECT OF COPYRIGHT
SURFACE FINISH:
WEIGHT: DRAWING EDITED BY:
13/12/2018
REV
02
UNLESS OTHERWISE SPECIFIED
DIMENSIONS ARE IN MILLIMETRES
SHEET
1-3 MORANG CR. MITCHELL PARK.
VICTORIA 3355 AUSTRALIA
PH: 03 5342 6399
DEBURR AND BREAK
SHARP EDGES
COENTURNER
14/12/2018
DRAWING CHECKED BY:
KG
DO NOT SCALE DRAWING
UNLESS OTHERWISE SPECIFIED
0. ± 1 ANGULAR ± 0.50°
0.0 ± 0.5
0.00 ± 0.25
A A
B B
C C
D D
6
6
5
5
4
4
3
3
2
2
1
1
12 bolts hold
the top cords
2 U-bolts
holding the
angled cord
Spacer inserts are used to
prevent deformation of the
upper chords when clamped.