manualshive.com logo in svg

Goldacres Super Cruiser G8, Руководство оператора, Страница: 10 / 210

Поделиться
Скачать
Goldacres Super Cruiser G8 Скачать руководство пользователя страница 10

6

 - Chapter 2 - Safety

G8 Super Cruiser Operator’s Manual MY19 - REV 0

Safety Information

Continued over page

The acid can cause blindness, burn skin and dissolve 

clothing. Batteries also produce flammable hydrogen 

gas (especially when charging), so keep them 

separated from any sources of sparks and flames.

A vigilant operator can avoid these hazards by:
1.  Wearing the correct personal protective 

equipment.

2.  Avoid spilling or dripping electrolyte.

3.  Place into a plastic collection tray ready for disposal 

if the case is found to be damaged.

EMERGENCY MEASURES

•  If the electrolyte gets in your eyes, flush your eyes 

with clean water for at least 15 minutes, then get 
immediate medical assistance. 

•  Also thoroughly wash all other affected areas on 

your body with water and remove all clothing.

•  If you swallow any electrolyte seek medical 

attention immediately.

Lifting Machine

 

Before raising the machine off the ground:

 Ensure that the boom is in its closed position. 

 Park on a flat level, firm area and engage the park 

brake.

 Empty the spray tank where possible. 

 Chock all wheels that remain on the ground.

 Securely lift the machine using a jack and support 

the machine on work stands. 

  Do not work under the machine when supported 

solely by a jack.

  Do not support the sprayer using materials that 

may crumble.

Changing Wheels & Tyres

 

An experienced person with the correct equipment 
should mount the wheels on the sprayer.
When changing a wheel on the sprayer ensure that 

the sprayer is on firm level ground and the wheels are 

chocked.

Tyre Maintenance

 

Maintain correct tyre pressure at all times. Inflation 

of tyres above or below the recommended pressure 
exerts additional pressure on the tyre, which may 
result in tyre damage.

Extreme caution is required during the inflation of 
tyres. If the tyre is inflated at a rapid rate separation 

and/or explosion of the rim can occur. This event can 

inflict serious or fatal injuries to the operator.

 Always use a tyre inflation gauge.

 Be proactive and continually check the condition of 

your tyres.

  Do not weld, heat or modify the rim.

Machine Operation

•  High speed turning places severe stresses on 

the wheels and axles and should be avoided. It 
is essential to observe the effects of turning on 
the open spray boom. Excessive turning speeds 
transmit great stresses to the spray boom and 
WILL CAUSE boom damage. 

•  Modification of the machine to increase maximum 

speed is STRICTLY PROHIBITED. This machine 

is designed for a maximum speed of 50 km/h. 
This speed must only be used on suitable terrain 
conditions. All components i.e. tyres, brakes, 
suspension, steering and chassis are designed and 
built to this maximum speed. 

•  MAXIMUM SPEED WHEN CORNERING, 

TURNING AT AN ANGLE GREATER THAN 
45

º

 OR DRIVING ON A SLOPE OR UNEVEN 

TERRAIN IS 5KM/H. When fitted with narrow 

wheel track and with high centre of gravity, the 
self-propelled sprayer may become unstable when 
turning at excessive speed or when operating on 
excessively steep terrain. 

•  Before leaving the sprayer the engine must be 

shut off, the transmission placed in neutral and 
the park brake engaged. NEVER ENGAGE THE 

PARK BRAKE WHILE THE SPRAYER IS MOVING. 

DAMAGE TO THE TRANSMISSION  MAY  RESULT.

Refuelling

•  Handle fuel with extreme caution. Do not refuel 

the machine while smoking or near open flames or 

sparks.

•  Always stop the engine before refueling the 

machine.

•  To prevent fires always keep the machine clean of 

grease, debris and dirt.

•  Do not use current emitting devices when re-

fuelling.

Collision Prevention & Warning 

Lights

•  Before operating the machine check with the 

relevant road management authorities for 
information regarding safe and legal transport on 
public roads in the state where the machine is 
being operated.

•  To assist in the prevention of collisions with other 

road users the Goldacres sprayers are fitted with 

warning lights and signs in accordance with national 
road regulations.

Содержание Super Cruiser G8



















































































































































































































Отзывы:

Нет отзывов