Genie Z-80/60 Скачать руководство пользователя | Manualshive

Страница: 56 / 65

background image

Operator's Manual

Sixth Edition • Sixth Printing

Transport and Lifting Instructions

54 Z-80/60

Part No. 226482

Transport and Lifting Instructions

Observe and Obey:



Genie provides this securement information as
a recommendation. Drivers are solely
responsible for making sure machines are
properly secured and the correct trailer is
selected pursuant to US Department of
Transportation regulations, other localized
regulations, and their company policy.



Genie customers needing to containerize any
lift or Genie product should source a qualified
freight forwarder with expertise in preparing,
loading and securing construction and lifting
equipment for international shipment.



Only qualified aerial lift operators should move
the machine on or off the truck.



The transport vehicle must be parked on a
level surface.



The transport vehicle must be secured to
prevent rolling while the machine is being
loaded.



Be sure the vehicle capacity, loading surfaces
and chains or straps are sufficient to withstand
the machine weight. Genie lifts are very heavy
relative to their size. See the serial label for the
machine weight.



Be sure the turntable is secured with the
turntable rotation lock before transporting. Be
sure to unlock the turntable for operation.



Do not drive the machine on a slope that
exceeds the uphill, downhill or side slope
rating. See Driving on a Slope in the Operating
Instructions section.



If the slope of the transport vehicle bed
exceeds the maximum slope rating, the
machine must be loaded and unloaded using a
winch as described in the brake release
operation.

Free-wheel Configuration for
Winching

Chock the wheels to prevent the machine from
rolling.

Release the non-steer
wheel brakes by turning
over the drive hub
disconnect caps.

Be sure the winch line is
properly secured to the
drive chassis tie points and
the path is clear of all
obstructions.

Reverse the procedures described to re-engage
the brakes.

Towing the Genie Z-80/60 is not recommended. If
the machine must be towed, do not exceed
3.2 km/h.

«
...
54
55
56
57
58
...
»

Содержание Z-80/60


































































Отзывы:

Нет отзывов

Похожие инструкции для Z-80/60

Genie GS-2668DC

Бренд: Terex Страницы: 48

Бренд: Xtreme Страницы: 80

Бренд: EASTMAN Страницы: 34

Бренд: Sinoboom Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды