background image

Sixth Edition • Sixth Printing

 

Operator's Manual

 

 

Work Area Safety 

 

 

Part No. 226482

 

Z-80/60 17 

 

 

 

Pipe Cradle Safety 

Read, understand and obey all warnings and 
instructions provided with the pipe cradles. 

Do not exceed the rated platform capacity. The 
pipe cradle assembly and the weight in the pipe 
cradles will reduce rated platform capacity and 
must be factored into total platform load. 

The pipe cradle assembly weighs 9.5 kg.  

The maximum capacity of the pipe cradle 
assembly is 91 kg. 

The weight of the pipe cradle assembly and the 
load in the pipe cradles may limit the maximum 
number of occupants in platform. 

Center the load within the perimeter of the 
platform. 

Secure the load to the platform. 

Do not obstruct the entrance or the exit of the 
platform. 

Do not obstruct the ability to operate the platform 
controls or the red Emergency Stop button. 

Do not operate unless you are adequately 
instructed and are aware of all of the hazards 
associated with movement of the platform with an 
overhanging load.  

Do not cause a horizontal force or side load to 
machine by raising or lowering a fixed or 
overhanging load. 

Electrocution Hazard:

 Keep pipes away from all 

energized electrical conductors. 

 

Panel Cradle Safety 

Read, understand and obey all warnings and 
instructions provided with the panel cradles. 

Do not exceed the rated platform capacity. The 
combined weight of the cradles, panels, occupants, 
tools and any other equipment must not exceed 
rated capacity. 

The panel cradle assembly weighs 13.6 kg.  

The maximum capacity of the panel cradles is 
113 kg. 

The weight of the panel cradles and the load in the 
panel cradles may limit the maximum number of 
occupants in platform to one person. 

Secure the cradles to the platform. Secure the 
panel(s) to the platform railing using the straps 
provided. 

Do not operate unless you are adequately 
instructed and are aware of all hazards associated 
with lifting panels.  

Do not cause a horizontal force or side load to 
machine by raising or lowering a fixed or 
overhanging load. 

Maximum vertical height of panels: 1.2 m 

Maximum wind speed: 6.7 m/sec 

Maximum panel area: 3 m

2

 

Содержание Z-80/60


































































Отзывы: