Genie Z-80/60 Скачать руководство пользователя

Страница: 28 / 65

Operator's Manual

Sixth Edition • Sixth Printing

Controls

26 Z-80/60

Part No. 226482

Platform Control Panel

Horn button

Press this button and the horn will sound.
Release the button and the horn will stop.

Platform not level indicator light

Level the platform until the light is off. The
platform level toggle switch will only work in
the direction that will level the platform.

Machine not level indicator light

Light is on when the platform is raised and the
machine is on a severe slope. The drive
function in one or both directions will not
operate.

Lower primary boom indicator light

Lower the primary boom until the light is off.

Not used

Used for optional equipment

Generator control with indicator light (if
equipped)

Move the switch or press the button to turn the
generator on. Move the switch again or
release the button to turn the generator off.

Emergency/Auxiliary power control with
indicator light

Use emergency/auxiliary power if the primary
power source (engine) fails.
Move and hold the switch or press and hold
the button. Activate the desired function. The
indicator light will be on when
emergency/auxiliary power is being used.

Diesel models:Glow plug control with indicator
light

Move the switch or push the button to activate
the glow plugs.

Diesel models:Automatic glow plug indicator
light

Amber light indicates glow plugs are on.

Gasoline/LPG models:Choke switch with
indicator light (if equipped)

Move the switch to activate the choke.

Engine start control with indicator light

Move the switch or push the button to start the
engine. The indicator light will be on when the
switch is moved or the button is pushed.

Engine idle control with indicator light

Move the switch or push the button to select
the engine idle setting. The indicator light next
to the current engine idle setting will be on.

Содержание Z-80/60


































































Результаты поиска

Содержание Z-80/60

Отзывы:

Похожие инструкции для Z-80/60

Бренды по названию

Популярные бренды

Genie Z-80/60, Руководство оператора

Результаты поиска

Содержание Z-80/60

Отзывы:

Похожие инструкции для Z-80/60

Бренды по названию

Популярные бренды