Gehl CTL55 Скачать руководство пользователя страница 44

Страница: 44 / 202

CONTROLS

Ignition Key

The Ignition key is used not only to start and
stop the engine, but also to lock and unlock
the following places:

�

Fuel ﬁller cap

�

Engine hood

�

Cab door

�

Manual storage

Doors and Covers

E4B003

Cab Door < CTL55 >

WARNING

�

When mounting and dismounting the

cab, ﬁrst open the door fully to the
stopped position and check that it
does not move.

�

When opening and closing the door,

grasp the handle securely and move
the door slowly. Opening the door
suddenly could result in it hitting your
head, or your hands or feet could get
caught.

Preparation before Opening and Closing
the Cab Door

1. Park the machine on a level surface and

stop the engine.

2. Raise the safety bar.

Lock and unlock

1. Insert and turn the ignition key.

Opening

1. Turn the handle (2) clockwise and open

the door fully.

To open the door from inside the cab:
1. Turn the handle (2) counterclockwise and

open the door fully.

Closing

1. Grasp the handle (2) or (3) and slowly

close the door.

T3B004

T3B005

T3B006

Содержание CTL55











































































































































































































Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды

Gehl CTL55, Руководство оператора

Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды