Gehl CTL55 Скачать руководство пользователя страница 51

Страница: 51 / 202

CONTROLS

Seat Belt < CTL55 >

CAUTION

Always fasten the seat belt securely
before starting the engine.

Fastening the seat belt

1. Adjust the seat to the optimum position

for operating, raise your torso, and sit
back ﬁrmly into the seat.

2. Pull on adjuster (A) in the manner shown in

the diagram to adjust the seat belt to the
desired length.

3. Make sure that the belt is not twisted, and

then insert the tongue plate (B) into the
buckle (C) of the seat belt until you hear a
clicking sound as it locks in place.

4. Pull the belt until you can feel the pressure

on your pelvis with the belt ﬁrmly in
place.

Seat and Seat Belt

C4C010

C4C011

Содержание CTL55











































































































































































































Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды

Gehl CTL55, Руководство оператора

Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды