Gehl CTL55 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 202

background image

MAINTENANCE

136

Every 250 Hours

Replacing the Air Cleaner
Elements

WARNING

Stop the engine and allow the machine to
cool before performing maintenance.

�

The engine, mufﬂer, radiator and many

other parts of the machine are hot
directly after the engine is stopped.
Touching these parts will cause burns.

IMPORTANT:  Do not use an element if its
ﬂutes, gaskets or seals are damaged.
IMPORTANT:  Be  sure  to  install  the
element  and  dust  cap  securely.  If  not,
dust  could  be  drawn  into  the  cylinder,
damaging the engine.
IMPORTANT:  Be sure to lock the air cleaner
after completing the maintenance.

1. Open the engine hood.

2. Push down the lever (6) to tilt up the air

cleaner.

3. Loosen the clamps (1) and remove the

dust cup (2).

4. Clean the inside of the dust cup (2).
5. Remove the outer element (3).
Do not yet remove inner element (5).
6. Clean the inside of the body (4).
7. Remove the inner element (5).
8. Install the new elements.
Press the elements ﬁrmly into the body

(4).

9. Install the dust cup (2) with the “UP” mark

at the top, then fasten it with the clamps
(1).

10. Push down the air cleaner and securely

lock it.

U1G008

6

U1G009

«
...
136
137
138
139
140
...
»

Содержание CTL55











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CTL55

Бренд: FENDT Страницы: 1245

Бренд: New Holland Страницы: 2

TN-A Series TN60A

Бренд: New Holland Страницы: 3

Бренд: Ventrac Страницы: 31

Бренд: Laney Страницы: 4

Бренд: Kubota Страницы: 28

Бренд: Kubota Страницы: 107

Бренд: Case IH Страницы: 15

TeeJet Matrix Pro 570G

Бренд: Spraying Systems Страницы: 127

Бренд: LSM Страницы: 44

Бренд: Tiger Страницы: 202

BENGAL JD6110-20M/R MY20

Бренд: Tiger Страницы: 223

BENGAL JD6110-30M/R T4F

Бренд: Tiger Страницы: 226

WILDKAT JD6105-25E T4F

Бренд: Tiger Страницы: 240

Бренд: Tiger Страницы: 236

BENGAL JD51 M Series

Бренд: Tiger Страницы: 240

WILDCAT JD6105D

Бренд: Tiger Страницы: 252

WILDKAT JD61 M/R Series

Бренд: Tiger Страницы: 258

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды