Gehl CTL55 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 202

background image

SAFETY

34

Maintenance Precautions

Have a Gehl technician repair
weld cracks or other damage

If welding must be performed, make sure that
it is done by a qualiﬁed person in a properly
equipped workplace. To prevent any part
from breaking down or be being damaged
due to overcurrent or sparks, observe the
following.

�

Disconnect the wiring from the battery

before doing electric welding.

�

Do not continuously apply 200V or more.

�

The earth ground must be connected

within one meter from the welding
section. Do not connect the earth ground
near to an electronically controlled device/
instrument or connectors.

�

Make sure that there are no seals or

bearings between the welding section
and the earth ground.

�

Do not connect the earth ground around

the pins for working equipment or
hydraulic cylinders.

�

When welding is to be done on the

machine body, disconnect the connectors
for the electronically controlled devices
before working.

Safety signs

�

Keep all safety signs clean and legible.

�

Replace all missing, illegible or damaged

safety and warning signs.

Vibrations to which the operator is
subjected

According to the results of the tests carried
out to determine the vibrations transmitted
to the operator by the machine, the upper
limbs are subjected to vibrations lower than
2.5 m (8.2 ft.) / s

2

, while the seated part of the

body is subjected to vibrations lower than
0.5 m (1.64 ft.) / s

2

.

Checks after maintenance

�

Gradually raise the engine speed from low

idle to maximum speed and check that
no oil or water is leaking from serviced
parts.

�

Move the controls and check that the

machine is operating properly.

Disposing of wastes

�

Pour waste ﬂuids from the machine into

containers. Disposing of ﬂuids improperly
destroys the environment.

�

Follow the prescribed regulations when

disposing of oil, fuel, engine coolant,
refrigerant, solvents, ﬁlters, batteries and
other harmful substances.

Handling of poisonous chemicals

Poisonous  chemicals  will  cause  serious
injury if directly contacted.
Poisonous  chemistry  used  in  this  machine
includes  grease,  battery  solution,  coolant,
paint and adhesive agent.

«
...
34
35
36
37
38
...
»

Содержание CTL55











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CTL55

Бренд: Vestil Страницы: 19

Бренд: Afron Страницы: 39

Бренд: Yanmar Страницы: 6

Бренд: Orwak Страницы: 28

Бренд: AGRI-COVER Страницы: 8

Бренд: Kubota Страницы: 114

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды