Gehl CTL55 Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 202

background image

167

TROUBLESHOOTING

Towing

WARNING

When  towing,  selecting  the  wrong  wire
rope,  inspecting  improperly,  or  towing
incorrectly  could  lead  to  accidents,
resulting in serious injury or death.

�

The wire rope breaking or detaching

could be extremely dangerous. Use
a wire rope suitable for the required
tractive force.

�

Do not use a wire rope that is kinked,

twisted or otherwise damaged.

�

Do not apply strong loads abruptly to

the wire rope.

�

Use safety gloves when handling the

wire rope.

�

Make sure there is an operator on the

machine being towed as well as on the
machine that is towing.

�

Never tow on slopes.

�

Do not let anyone near the wire rope

while towing.

Towing the Machine

Use the procedure described below to tow
light weight objects or the machine itself if it
is stuck in the mud and not able to get out
on its own.

IMPORTANT: Do not tow a machine if its
engine does not start or if the machine
does not run. Doing so could damage the
machine being towed.

IMPORTANT: Be sure to follow all the
steps below closely when towing. Failure
to heed even one of the steps may cause
damage to the hooks (1).

�

Maximum tractive force

  CTL55: 42.0 kN (9450 lbf) or less
  CTL65: 56.8 kN (12780 lbf) or less
  CTL75: 68.4 kN (15370 lbf) or less
  CTL85: 78.9 kN (17750 lbf) or less

1. Attach the wire ropes (2) to the hooks (1)

as shown in the ﬁgure.

2. Make the wire rope horizontal and line up

straight with the travel frame.

3. Move the machine to tauten the wire

rope.

4. Move the machine slowly and tow.

Applicable machine models

CTL55: 222000440 or later
CTL65: 223000838 or later
CTL75: 224000543 or later
CTL85: 225000633 or later

«
...
167
168
169
170
171
...
»

Содержание CTL55











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CTL55

Бренд: New Holland Страницы: 41

Бренд: New Holland Страницы: 51

RK19 Hydrostatic

Бренд: Rural King Страницы: 156

Бренд: Bolens Страницы: 19

Бренд: Bolens Страницы: 104

Бренд: KitchenAid Страницы: 2

TRAC-LIFT T50HLSS

Бренд: JAWA Страницы: 11

Бренд: Whirlpool Страницы: 16

Бренд: Yanmar Страницы: 170

Profile GCG1580L

Бренд: GE Страницы: 2

Бренд: Trac Vac Страницы: 9

Бренд: Peg-Perego Страницы: 11

AERA-vator AE40L

Бренд: First Products Страницы: 31

2000 super dexta

Бренд: Ford Страницы: 139

Бренд: Ford Страницы: 258

Бренд: Toro Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды