Gehl CTL55 Скачать руководство пользователя страница 135

Страница: 135 / 202

133

MAINTENANCE

Every 50 Hours

Inspecting the Bucket Stoppers
(bolts / nuts)

WARNING

Before performing maintenance or
repairs under the machine, set all working
equipment against the ground or in the
lowermost position.

1. Park the machine on ﬁrm, level ground

and remove the bucket.

2. Retract the bucket cylinders and lift arm

cylinders to the minimum length.

3. Inspect the adjusting bolts (1) and lock

nuts (2) for bending, denting, deformation
and looseness.

4. If there are any irregularities with the

adjusting bolts (1) and lock nuts (2).

Refer to page 140, “Adjusting or Replacing

the Bucket Stoppers (bolts/nuts)”.

Содержание CTL55











































































































































































































Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды

Gehl CTL55, Руководство оператора

Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды