Gehl CTL55 Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 202

background image

CONTROLS

48

Seat and Seat Belt

Seat < CTL55 >

WARNING

Adjust, secure and latch the operator’s
seat.

(A) Seatback angle adjustment

1. Raise your torso, and sit down ﬁrmly in

the seat.

2. Pull on lever (1) to use the force of the

springs  in  the  seatback  to  adjust  the
reclining angle. Release the lever (1) at the
desired  angle  and  the  seatback  will  be
locked in that position.
  Adjustment range ..................... 15 deg.

(B) Fore-and-aft adjustment

1. Pull on lever (2) and slide the seat rearward

or forward to bring it to the optimum
position for operating the machine.

2. Release the lever (2) at the desired position

and the seat will be locked there.

Adjustment range: 130 mm (5.1 in.)

(C) Weight adjustment

1. Pull on and shift the lever (3) to right side

or left side, to adjust the seat suspension
according to the operator’s weight.
•  Right .............Light operator
•  Middle ..........Medium weight operator
•  Left ...............Heavy operator

«
...
48
49
50
51
52
...
»

Содержание CTL55











































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CTL55

Бренд: Challenger Страницы: 61

Бренд: Case IH Страницы: 41

Бренд: Iseki Страницы: 98

Бренд: Iseki Страницы: 176

Бренд: Komatsu Страницы: 8

WEATHERBRAKE 307022172

Бренд: Femco Страницы: 7

GE PROFILETM GCG1500L

Бренд: GE Страницы: 2

Бренд: GreenTec Страницы: 27

Multi Carrier HXF 3302

Бренд: GreenTec Страницы: 23

Бренд: GreenTec Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды