Gehl CTL55 Скачать руководство пользователя страница 120

Страница: 120 / 202

MAINTENANCE

118

< CTL85 >

1. Open the rear door.
2. Inspect the water separator (1).
If the red indicator ring (6) is sunk to the

bottom of the case (4), no water is mixed
in.

If the red indicator ring (6) is ﬂoating, there

is water up to the bottom of the ring. Drain
the water and clean.

Refer to page 134, “Cleaning the Water

Separator.”

Inspecting the Fuel Level

WARNING

�

Do not smoke or permit open

ﬂames while fueling or near fueling
operations.

�

Stop the engine in a well-ventilated

place when adding fuel.

�

Clean up spilled fuel immediately.

�

Do not ﬁll the fuel tank to capacity.

Allow room for expansion.

�

Tighten the fuel ﬁller cap securely.

1. Check the fuel level using the fuel gauge

(1).
F: full
E: empty

2. If the level is low, add fuel from the fuel

port (2) while watching the fuel gauge (1).

Refer to page 47, “Fuel Filler Cap.”

Daily Inspection (Every 10 Hours)

T7G0071

Содержание CTL55











































































































































































































Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды

Gehl CTL55, Руководство оператора

Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды