Gehl CTL55 Скачать руководство пользователя страница 85

Страница: 85 / 202

OPERATION

Operating Procedures

�

Do not attempt a spin turn or pivot turn at

high speeds.

Doing so may cause extreme wear and/or

the tracks to come off.

�

Do not cut across a slope.

Doing so may cause extreme wear and/or

the tracks to come off.

�

Do not exceed the loader’s rated operating

capacity.

�

Do not use buckets or attachments that

exceed the loader’s operating capacity.

�

Do not use the downward force of the

bucket to drive piles.

�

Do not dig down deeply with the bucket.

Doing so could damage the bucket and
lift arms.

�

Hitting the bucket against rocks, etc.,

could damage the bucket or the bucket
cylinders.

T7D025

T7D026

T7D027

T7D028

T7D030

T7D029

Содержание CTL55











































































































































































































Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды

Gehl CTL55, Руководство оператора

Результаты поиска

Содержание CTL55

Отзывы:

Похожие инструкции для CTL55

Бренды по названию

Популярные бренды