EN
EN
60
61
Then start a coffee brewing function for rinsing the espresso filter with water (e.g.
“Coffee Beverages / Espresso / 2 cups”).
3. If the opening in the bottom of a double-wall filter is clogged, you may use the
fine needle of the cleaning tool for piercing it open.
4. The mesh of the espresso filters may be cleaned in circling movements via a fine
brush. Thereafter, rinse with clear tap water.
Thorough Cleaning
WARNING
– Filter holder and espresso fitler will be very hot after using
the cleaning funcion.
5. First, remove any residues of coffee powder from the espresso filter.
6. Put a cleaning tablet into the espresso filter (without coffee powder!).
7. Install the espresso filter via the filter holder at the group head, and start the
cleaning function “Guide and Setting / Mainenance / Cleaning cycle‘). Let the
appliance operate, until the cleaning cycle ran through.
8. Remove the filter holder from the group head and wipe the espresso filter and
filter holder with clear, warm water and a soft sponge or cloth for removing any
residues of the cleaning tablet.
9. Replace the filter holder at the group head (without coffee powder) and start the
brewing function (e.g. “Coffee Beverages / Espresso / 2 cups”).
CLEANING THE HOUSING AND THE WARMING TRAY
We recommend to wipe the housing and the warming tray via a soft moist cloth.
Thereafter polish via a soft dry cloth.
CLEANING THE DRIP TRAY
WARNING
– The contents of the drip tray may be hot.
At least at the end of the day or when the filling indicator sticks out significantly of
the metal grid, you need to empty the drip tray. Carefully avoid to spill the contents
of the drip tray. This holds especially, when the drip tray is really full.
1. Pull out the drip tray carefully. Remove the metal grid and the red filling indicator.
Empty the drip tray. Pull the cover at the rear of the drip tray upwards and out.
2. Wash the parts via some warm dishwater and a soft cloth. Thereafter rinse with
clear water and wipe dry.
3. Place the cover at one side onto the rear chamber of the drip tray and push the
cover down until it clicks into place. Place the filling indicator onto the post in
the drip tray and turn it until it slides down.
4. Replace the metal grid. If filling indicator and metal grid are inserted correctly,
the metal grid lies stably.
CLEANING THE GRINDER
If the grinder is blocked or you wish to clean the grinder, you can remove the grin-
der sleeve (central part of the grinder) from the grinder chute.
CAUTION
– Do not let the parts of the grinder get in contact with any liquids
to avoid damage to the grinder. In normal conditions, only turn the grind size dial,
while the grinder is operating. However, when the grinder is blocked and does not
start, immediately touch the “Stop” button to avoid overloading the motor. In this
case,
as an exception
, you must turn the grind size dial, while the grinder is idle.
IMPORTANT -
Whenever possible,
remove all coffee beans from the bean hop-
per, before disassembling the grinder
. Otherwise, the coffee beans fall into the
grinder chute and may get wedged therein. In this case, removing the coffee
beans and cleaning the grinder may be quite difficult. Whats more, with coffee
beans in the grinder chute, it may be impossible to reassemble the grinder.
1.
Emptying the bean hopper:
Remove the coffee beans from the bean hopper.
When the grinder is not blocked, we recommend to grind the residues of cof-
fee beans. For this, place a suited vessel under the grinder outlet. From the
home page, select the command “Coffee Beverages / Espresso / 2 cup” and,
if required, touch the bean icon repeatedly, until the grinder is empty and the
grinder noise changes remarkably.
2.
Removing the grinder sleeve:
While the grinder is operating (in case that the
grinder is not blocked), turn the grind size dial leftwards to grind size 11. Then
switch off the appliance and unplug. Turn the locking knob in the centre of the
bean hopper counter-clockwise for unlocking the grinder. Pull the grinder sleeve
out of the grinder chute.
3.
Cleaning the grinder:
Brush the grinder chute (in the appliance) and the grinder
sleeve via a
dry
nylon brush. You may use the provided cleaning brush. Clean
the grinder adapter and grinder outlet via a
dry
, soft cloth or a
dry
, soft brush.
4.
Re-assembling the grinder sleeve:
Hold the grinder sleeve by the locking knob
and insert it into the grinder chute. Turn the locking knob, while slightly pressing
it down until the grinder sleeve sildes down. Turn the locking knob clockwise to
the stop for locking the grinder.
